background image

 

 

SAFETY INSTRUCTIONS 

 

WARNING 

THIS EQUIPMENT CONTAINS LETHAL VOLTAGE LEVELS.  INSTALLATION AND SERVICING 
MUST BE PERFORMED BY QUALIFIED PERSONNEL 
 

IMPORTANT:  SAVE THESE INSTRUCTIONS! 

READ  AND  FOLLOW  ALL  INSTRUCTIONS  BEFORE  INSTALLING,  OPERATING,  OR 
SERVICING  CHARGER.    ANY  DEVIATION  CAN  CAUSE  SERIOUS  AND  PERMANENT 
DAMAGE.  FAILURE TO FOLLOW THE INSTRUCTIONS VOIDS THE WARRANTY. 
 
 

1. 

Install and ground the charger in accordance with the National Electric Code and your local electric 
code.  Failure to properly ground the charger could result in a fatal electric shock. 

 
2. 

“CAUTION” – Risk of fire. Use only on circuits provided with 30 amperes branch circuit protection in 
accordance with the National Electrical Code, NFPA70. 

 
3. 

To  reduce  the  risk  of  fire,  install  chargers  on  a  surface  of  non-combustible  material,  such  as 
concrete, stone, brick or grounded metal. 

 
4. 

This  charger  has  been  designed  to  charge  many  chemistries  of  battery,  the  appropriate  charge 
algorithm for the chemistry of battery to be charged must be set in the controller. (Lead-acid flooded 
or sealed, Ni-Cad and Lithium Ion) 

 
5. 

Connect only batteries of the same number of cells as listed on the charger nameplate.  Damage to 
the battery could occur, particularly if the battery has fewer cells than the rating of the charger. 

 
6. 

Do not touch uninsulated parts of the output connector or battery terminals.  A possibility of serious 
electrical shock exists. 

 
7. 

During charge, batteries produce hydrogen gas, which can explode if ignited.  Never smoke, use an 
open flame, or create sparks in the vicinity of the battery.  Ventilate well when the battery is in an 
enclosed space. 

 
8. 

Do not connect or disconnect the battery plug while the charger is on.  Doing so will cause arching 
and burning of the connector possibly resulting in charger damage or battery explosion and will void 
the charger warranty. 

 
9. 

Lead-acid batteries contain sulfuric acid, which is caustic and can cause chemical burns to the skin. 
Refer to the battery manufacturer’s instructions for safe handling of batteries. Use proper personnel 
protective equipment.  Do not get in eyes, on skin, or on clothing.  In cases of contact with eyes, 
flush immediately with clean water for 15 minutes.  Seek medical attention immediately. 

 
10. 

Do  not  operate  the  charger  with  any  panels  removed.    De-energize  all  AC  and  DC  power 
connections before servicing the charger. 

 
11. 

The charger is not for outdoor use.   Do not expose the charger to water spray, rain or snow. 

 
12. 

Do  not  operate  the  charger  with  damaged  cables,  including  cables  with  exposed  conductors  or 
damaged connectors.  Replace damaged cables before operation. 

 
13. 

Do not operate the charger if it has been dropped, received a sharp blow, or otherwise damaged in 
any way.  Call your service representative. 

Содержание HIGH FREQUENCY Series


















Отзывы: