6
FS5.3e Elliptical
1. Set the main body of the elliptical on the floor and slide the Rear Rail
Assembly (
2
) into the bracket on the stabilizer of the main body.
Position the rail assembly so the mounting holes line up with the holes
in the stabilizer bracket of the main body.
2. Install the four Hex Head Bolts (
102
), Split Washers (
151
), Flat
Washers (
142
), and Star Washers (
154
) through the top of the stabilizer
first.
Make sure the washers are installed on the bolt in the correct
order: the split washer is put on first, the flat washer, and the star
washer last. The star washer needs to be in contact with the
painted surface of the rail frame to ensure a good ground.
Hand
tighten them only at this point until the next two bolts are installed. Install
the two Hex Head Bolts (
104
) and Flat Washers (
137
) through the sides
of the stabilizer bracket. Fasten two Nyloc Nuts (
130
) onto the bolts.
Hand-tighten them at first until both bolts have been started, then tighten
all six bolts (
102
&
104
) as tight as possible.
3. At the top opening of the main body locate the Computer Cable (
44
).
Unravel the cable and feed the Computer Cable into the bottom of the
Console Mast Tube and out of the top opening. Install the Console Mast
into the receiving bracket on the top of the main body, pulling slightly
on the Computer Cable at the top of the mast while installing; this will
ensure the cable does not get pinched and shorted out during assembly.
There is one bolt that is pre-installed in the receiving tube that will slide
into the slots at the bottom of the mast.
4. Install the two Hex Head Bolts (
103
) and Curved Washers (
153
) through
the front of the console mast; just hand tighten for now. Install the Hex
Head Bolt (
105
) and Split Washer (
152
) through the left side of the
console. Tighten all three installed bolts (
103
&
105
) and the
pre-installed bolt as tight as possible.
NOTE: The Computer Cable runs through the Console Mast Tube. Be
careful not to damage or pinch this cable during this procedure as
damage to the electronics could result.
5. There are three connectors at the top opening of the Console Mast (
12
),
two Hand Pulse Wires (
48
) and one Computer Cable (
44
). Connect
these to the mating connectors on the back of the Console Assembly
(
43
). Store the excess wiring back into the Console Mast (
12
) as you
carefully install the Console Assembly (
43
) onto the mounting plate of
Console Mast. Secure the Console with four Phillips Head Screws (
116
).
Be careful not to pinch any wires.
6. Install the water bottle holder onto the handlebar in any position you like.
FS5.3e
Assembly Instructions
Hardware Step 1
Rear Rail, Console Mast & Console
#102
. 5/16” x 2-1/4”
Hex Head Bolt (4 pcs)
#103
. 3/8” x 3/4”
Hex Head Bolt (2 pcs)
#104
. 3/8” x 1-1/2”
Hex Head Bolt (2 pcs)
#105
. 3/8” x 2-1/4”
Hex Head Bolt (1 pc)
#116
. M5 x 10mm
Phillips Head Screw
(4 pcs)
#130
. 3/8” x 7T
Nyloc Nut (2 pcs)
#137
. 3/8” x 19 x 1.5T
Flat Washer (2 pcs)
#142
. 5/16” x 20 x 1.5T
Flat Washer (4 pcs)
#151
. 5/16” x 1.5T
Split Washer (4 pcs)
#152
. 3/8” x 2T
Split Washer (1 pc)
#153
. 3/8” x 23 x 2T
Curved Washer (2 pcs)
#154
. 5/16”
Star Washer (4 pcs)
1