background image

Congratulations on the purchase of your XpressFill Bottle filling machine.

Thank you for choosing our handcrafted bottle filler as the technology to bottle your passion. We look forward to
assisting you in experiencing the best performance from your filler.

This manual is written with your safety and convenience in mind. We highly recommend reading the manual before
using your filler for the first time.

If you have any questions or comments, please do not hesitate to contact us.

XpressFill Systems LLC

265 Prado Road, Suite 1

San Luis Obispo, CA 93401

US

805.541.0100

Toll free 844.361.2750

[email protected]

www.xpressfill.com

Important Safety Instructions

Misuse of the bottle-filling machine can result in serious injury or death. Do not use the machine in any way not
covered in this manual or for any purpose other than those explained in the following pages.

Severe product damage and/or injury could result from the use of unqualified Service Technicians or non-original
replacement parts. All repairs must be performed by a qualified Service Technician or with the approval from an
XpressFill Technician. Only original factory replacement parts should be used.

Electrical shock or fi re could result if the electrical supply for the bottle filler covered in this manual is not correctly
installed or if the bottle filler has been improperly grounded. Do not use the bottle filler covered in this manual
unless you are certain the electrical supply has been correctly installed and the bottle filler has been properly
grounded.

265 Prado Road, Suite 1 | San Luis Obispo, CA 93401 | 805.541.0100   |  xpressfill.com  |  [email protected]

3

|  XpressFill Systems LLC

Содержание XF4500























Отзывы: