XpressFill XF4500 Скачать руководство пользователя страница 2

ii

 | 

XPRESSFILL Systems LLC

265 Prado Road, Suite 1  •  San Luis Obispo, CA 93401  •  Tel: (805) 541-0100  •  [email protected]

 lling machine.

  ank you for choosing our handcrafted bottle fi ller as the technology to bottle your passion.  We 

look forward to assisting you in experiencing the best performance from your fi ller.

  is manual is written with your safety and convenience in mind.  We highly recommend reading 

the manual before using your fi ller for the fi rst time.

If you have any questions or comments, please do not hesitate to contact us.

XpressFill Systems LLC

265 Prado Road, Suite #1

San Luis Obispo, CA 93401

USA

(805) 541-0100

 ll.com

 ll.com

Important Safety Instructions

Misuse of the bottle-fi lling machine can result in serious injury or death.  Do not use the machine 
in any way not covered in this manual or for any purpose other than those explained in the 
following pages.

Severe product damage and/or injury could result from the use of unqualifi ed Service 
Technicians or non-original replacement parts.  All repairs must be performed by a qualifi ed 
Service Technician or with the approval from an XpressFill Technician.  Only original factory 
replacement parts should be used.

Electrical shock or fi re could result if the electrical supply for the bottle fi ller covered in this 
manual is not correctly installed or if the bottle fi ller has been improperly grounded.  Do not 
use the bottle fi ller covered in this manual unless you are certain the electrical supply has been 
correctly installed and the bottle fi ller has been properly grounded.

Содержание XF4500
















Отзывы: