Xinje DS2-20P2-AS Скачать руководство пользователя страница 9

Страница: 9 / 50

MS series servo motors can be installed either horizontally or vertically.

(5) Avoid oil and water

Install a protective cover over the

servomotor if it is used in a location that is

subject to water or oil mist. Also use a

servomotor with an oil seal when needed

to seal the through-shaft section.

(6) Cable stress

Make sure that the power lines are free from bends and tension. Be especially careful

to wire signal line cables so that they are not subject to stress because the core wires

are very thin, measuring only 0.2 to 0.3mm

2. Servo drive

The DS2 series servo drivers are base-mounted servo drivers. Incorrect installation

will cause problems. Follow the installation instructions below

(1) Storage temperature

Store the servo driver within -20~+85

℃

, as long as it is stored with the power cable

disconnected.

(2) Installation location

The following precautions apply to the installation site.

Situation

Installation Precaution

Installation in a

Control Panel

Design the control panel size, unit layout, and cooling method

so the temperature around the servo drivers does not exceed

Through part of

the shaft

Содержание DS2-20P2-AS



















































Результаты поиска

Содержание DS2-20P2-AS

Отзывы:

Бренды по названию

Популярные бренды

Xinje DS2-20P2-AS, Руководство пользователя

Результаты поиска

Содержание DS2-20P2-AS

Отзывы:

Бренды по названию

Популярные бренды