Xilinx Virtex-4 RocketIO Скачать руководство пользователя страница 92

Страница: 92 / 176

www.xilinx.com

Embedded Tri-Mode Ethernet MAC User Guide

UG074 (v2.2) February 22, 2010

Chapter 3:

Client, Host, and MDIO Interfaces

0x390

E0_GENERALCONFIG

Promiscuous mode,

0x00000000

bits

[31:0].

0x390

R/W

0x394:0x39F

Reserved.

0x3A0

IRSTATUS

Access done, interrupt request status.

0x3A0

R/W

0x3A4

IRENABLE

Interrupt request enable.

0x3A4

R/W

0x3A8:0x3AF

Reserved.

0x3B0

MIIMWRDATA

MDIO write data.

0x3B0

R/W

0x3B4

MIIMCNTL

Decode address for MDIO
address output.

0x3B4

0x3B8:0x5FF

Reserved.

EMAC1 Registers

0x600

E1_RXCONFIGW0

Receiver configuration word 0.

0x600

R/W

0x640

E1_RXCONFIGW1

Receiver configuration word 1.

0x640

R/W

0x680

E1_TXCONFIG

Transmitter configuration.

0x680

R/W

0x6C0

E1_FLOWCONTROL

Flow control configuration.

0x6C0

R/W

0x700

E1_EMACCONFIG

Ethernet MAC configuration.

0x700

R/W

0x720

E1_RGMII_SGMII RGMII/SGMII configuration.

0x720

0x740

E1_MGMTCONFIG

Management configuration.

0x740

R/W

0x780

E1_UNICASTADDRW0

Unicast address [31:0].

0x780

R/W

0x784

E1_UNICASTADDRW1

0x0000

, Unicast Address [47:32].

0x784

R/W

0x788

E1_ADDRTABLECONFIGW0

Multicast address data[31:0]

0x788

R/W

0x78C

E1_ADDRTABLECONFIGW1

0x00,

RNW,

00000,

ADDR[1:0],

Multicast address data[47:32].

0x78C

R/W

0x790

E1_GENERALCONFIG

Promiscuous mode,

0x00000000

bits

[31:0].

0x790

R/W

0x7A0

IRSTATUS

Access done, interrupt request status.

0x7A0

R/W

0x7A4

IRENABLE

Interrupt request enable.

0x7A4

R/W

0x7A8:0x7AF

Reserved.

0x7B0

MIIMWRDATA

MDIO write data.

0x7B0

R/W

0x7B4

MIIMCNTL

Decode address for MDIO
address output.

0x7B4

0x7B8:0x7FF

Reserved.

Table 3-30:

Detailed Address Codes for DCR Host Bus Access

(Cont’d)

Address

Codes

Register Names

Description

Ethernet MAC

Register Address

R/W

www.BDTIC.com/XILINX

Содержание Virtex-4 RocketIO

















































































































































































Результаты поиска

Содержание Virtex-4 RocketIO

Отзывы:

Бренды по названию

Популярные бренды

Xilinx Virtex-4 RocketIO, Руководство пользователя

Результаты поиска

Содержание Virtex-4 RocketIO

Отзывы:

Бренды по названию

Популярные бренды