manualshive.com logo in svg

Xilinx Virtex-4 RocketIO, Руководство пользователя

Поделиться
Скачать
Xilinx Virtex-4 RocketIO Скачать руководство пользователя страница 74

74

www.xilinx.com

Embedded Tri-Mode Ethernet MAC User Guide

UG074 (v2.2) February 22, 2010

Chapter 3:

Client, Host, and MDIO Interfaces

R

Host Clock Frequency

The host clock (HOSTCLK) is used to derive the MDIO clock, MDC, and is subject to the 
same frequency restrictions. See the 

Virtex-4 FPGA Data Sheet

 for the HOSTCLK frequency 

parameters.

Configuration Registers

The Ethernet MAC has seven configuration registers. These registers are accessed through 
the host interface and can be written to at any time. Both the receiver and transmitter logic 
only respond to configuration changes during IFGs. The configurable resets are the only 
exception, because the reset is immediate.

Configuration of the Ethernet MAC is performed through a register bank accessed through 
the Host interface. Any time an address shown in 

Table 3-7

 is accessed, a 32-bit read or 

write is performed from the same configuration word, with the exception of the read-only 
Ethernet MAC mode configuration register and the RGMII/SGMII configuration register. 
Only the speed selection is both readable and writable in the Ethernet MAC mode 
configuration register. 

 

The configuration registers and the contents of the registers are shown in 

Table 3-8

 through 

Table 3-14

.

Table 3-6:

Management Interface Transaction Types

Transaction

HOSTMIIMSEL

HOSTADDR[9]

Configuration/Address Filter

0

1

MDIO access

1

X

Table 3-7:

Configuration Registers

{HOSTEMAC1SEL, HOST_ADDR[9:0]}

Register Description

0x200

Receiver Configuration (Word 0)

0x240

Receiver Configuration (Word 1)

0x280

Transmitter Configuration

0x2C0

Flow Control Configuration

0x300

Ethernet MAC Mode Configuration

0x320

RGMII/SGMII Configuration

0x340

Management Configuration

Notes: 

1. HOSTEMAC1SEL acts as bit 10 of HOSTADDR.

www.BDTIC.com/XILINX

Содержание Virtex-4 RocketIO

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды