Xilinx RocketIO Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 156

background image

RocketIO™ Transceiver User Guide

73

UG024 (v3.0) February 22, 2007

Clock Recovery

R

Similarly, if RXUSRCLK is slower than RXRECCLK, the buffer fills up over time. The clock
correction logic corrects for this by incrementing the read pointer to skip over a removable
byte sequence that need not appear in the final FPGA core byte stream. This is shown in the
bottom buffer,

, where the solid read pointer increments to the value

represented by the dashed pointer. This accelerates the emptying of the buffer, preventing
its overflow. The transceiver design skips a single byte sequence, when necessary, to
partially empty a buffer. If attribute CLK_COR_REPEAT_WAIT is 0, the transceiver can
also skip four consecutive removable byte sequences in one step, to further empty the
buffer when necessary.

These operations require the clock correction logic to recognize a byte sequence that can be
freely repeated or omitted in the incoming data stream. This sequence is generally an IDLE
sequence, or other sequence comprised of special values that occur in the gaps separating
packets of meaningful data. These gaps are required to occur sufficiently often to facilitate
the timely execution of clock correction.

The clock correction logic has the ability to remove up to four IDLE sequences during a
clock correction. How many IDLEs are removed depends on several factors, including
how many IDLEs are received and whether CLK_COR_KEEP_IDLE is TRUE or FALSE.
For example, if three IDLEs are received and CLK_COR_KEEP_IDLE is set to TRUE, at
least one IDLE sequence must remain after clock correction has been completed. This
limits the clock correction logic to remove only two of the three IDLE sequences. If
CLK_COR_KEEP_IDLE is FALSE, then all three IDLEs can be removed.

illustrates the relationship between the number of IDLE sequences removed, the

inherent stability of REFCLK, and the number of bytes allowed between clock correction
sequences.

Ports and Attributes

CLK_CORRECT_USE

This attribute controls whether the PCS will repeat/skip the clock correction sequences
(CCS) from the elastic buffer to compensate for differences between the clock recovered
from serial data and the reference clocks. When this attribute is set to TRUE, the clock
correction is enabled. If set to FALSE, clock correction is disabled. When clock correction is
disabled, RXRECCLK must drive the receive logic in the fabric. Otherwise, the elastic
buffer may over/underflow.

Table 2-14:

Data Bytes Allowed Between Clock Corrections as a Function of

REFCLK Stability and IDLE Sequences Removed

Bytes Allowed Between Clock Correction Sequences

(1)

REFCLK

Stability

Remove 1 IDLE

(2)

Sequence:

Remove 2 IDLE

Sequences:

Remove 3 IDLE

Sequences:

Remove 4 IDLE

Sequences:

100 ppm

5,000

10,000

15,000

20,000

50 ppm

10,000

20,000

30,000

40,000

20 ppm

25,000

50,000

75,000

100,000

Notes:

1. All numbers are approximate.
2. IDLE = the defined clock correction sequence.

Product Not Recommended for New Designs

«
...
71
72
73
74
75
...
»

Содержание RocketIO





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для RocketIO

Бренд: X10 Страницы: 1

Бренд: Vestil Страницы: 8

Бренд: Hallicrafters Страницы: 9

Бренд: Proteco Страницы: 9

Advantage III Gold Series

Бренд: Ebtron Страницы: 24

Бренд: Small Wonder Labs Страницы: 26

Бренд: gefran Страницы: 8

Бренд: Micrel Страницы: 47

Бренд: Doro Страницы: 12

Бренд: Olson Technology Страницы: 12

Gewa Control Easy HM

Бренд: Abilia Страницы: 12

Бренд: VPC Страницы: 2

Бренд: AKG Страницы: 125

Бренд: Nicols Страницы: 12

FMT 380 BT CHARGE

Бренд: Hyundai Страницы: 24

Бренд: Altinex Страницы: 8

Бренд: SMAR Страницы: 44

Бренд: ABACOM Technologies Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды