Xilinx LogiCORE IP Spartan-6 Скачать руководство пользователя страница 21

Страница: 21 / 51

Spartan-6 FPGA GTP Transceiver Wizard v1.8

www.xilinx.com

UG546 (v1.8) December 14, 2010

Generating the Core

Line Rate and Protocol Template

The Line Rate and Protocol Template screen (page 2) of the Wizard (

Figure 3-6

) allows you

to select the line rate, reference clock frequency, encoding/decoding method, and data
width. In addition, this page specifies protocol templates.

Place a check next to the

Use Dynamic Reconfiguration Port

option if you wish to

bring this signal out for use by the application.

Note:

In all of the following tables, options not used by the PCI EXPRESS example are shaded.

The remaining options are divided into GTP0 and GTP1 groups with identical parameters.
These apply to the two GTP transceivers present in each GTPA1_DUAL primitive. The
remaining discussion in this chapter describes only the GTP0 portion.

From the Protocol Template list, select

Start from scratch

if you wish to manually set

all parameters.

Select one of the available protocols from the list to begin your design with a pre-
defined protocol template. For GTP1 only, select

Use GTP0 settings

to automatically

copy the settings from GTP1. The PCI EXPRESS example uses the

pcie

protocol

template. Because both transceivers are configured identically, the protocol template
option for GTP1 is set to

Use GTP0 settings

X-Ref Target - Figure 3-6

Figure 3-6:

Line Rates and Protocol Template - Page 2

Содержание LogiCORE IP Spartan-6




















































Результаты поиска

Содержание LogiCORE IP Spartan-6

Отзывы:

Похожие инструкции для LogiCORE IP Spartan-6

Бренды по названию

Популярные бренды

Xilinx LogiCORE IP Spartan-6, Руководство по началу работы

Результаты поиска

Содержание LogiCORE IP Spartan-6

Отзывы:

Похожие инструкции для LogiCORE IP Spartan-6

Бренды по названию

Популярные бренды