Xilinx LogiCORE IP Spartan-6 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 51

Xilinx LogiCORE IP Spartan-6 Скачать руководство пользователя страница 37

Spartan-6 FPGA GTP Transceiver Wizard v1.8

37

UG546 (v1.8) December 14, 2010

Generating the Core

describes the Channel Bonding sequence definition.

Table 3-23, page 38

describes the Clock Correction settings.

Table 3-21:

Channel Bonding Setup

Options

Description

Use Channel Bonding

Enables receiver channel bonding logic using unique character sequences. When recognized,
these sequences allow for adding or deleting characters in the receive buffer to byte-align
multiple data transceivers.

Master Transceiver

Indicates which transceiver from the selected pair(s) will function as the Channel Bonding
master.

Use Two Channel
Bonding Sequences

Activates the optional second Channel Bonding sequence. Detection of either sequence
triggers channel bonding.

Sequence Length

Select from the drop down list the number of characters in the unique channel bonding
sequence.

The PCI EXPRESS example uses

4

.

Sequence 1 Max Skew

Select from the drop down list the maximum skew in characters that can be handled by
channel bonding. Must always be less than the minimum distance between channel bonding
sequences.

The PCI EXPRESS example uses

7

.

Sequence 2 Max Skew

Same as Sequence 1 max skew.

Table 3-22:

Sequence Definition

Option

Description

Byte (Symbol)

Set each symbol to match the pattern the protocol requires. The PCI EXPRESS sequence length is 8
bits.

01001010

is used for the first three symbols of sequence 1. Symbol 4, sequence 1 and symbol

3, sequence 2 are set to

10111100

. Symbols 1 and 2 of Sequence 2 are set to

00111100

. Symbol 4

of Sequence 2 is set to

00011100

.

K Character

This option is available when 8B/10B decoding is selected. When checked, the symbol is an 8B/10B
K character.

Inverted Disparity

Some protocols with 8B/10B decoding use symbols with deliberately inverted disparity. This
option should be checked when such symbols are expected in the sequence.

Don’t Care

Multiple-byte sequences can have wild card symbols by checking this option. Unused bytes in the
sequence automatically have this option set.

«
...
35
36
37
38
39
...
»

Содержание LogiCORE IP Spartan-6




















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды