manualshive.com logo in svg

Xilinx LogiCORE IP Spartan-6, Руководство по началу работы

Поделиться
Скачать
Xilinx LogiCORE IP Spartan-6 Скачать руководство пользователя страница 38

38

www.xilinx.com

Spartan-6 FPGA GTP Transceiver Wizard v1.8

UG546 (v1.8) December 14, 2010

Chapter 3: 

Running the Wizard

Table 3-23: 

Clock Correction

Option

Description

Use Clock Correction

Enables receiver clock correction logic using unique character sequences. When recognized, 
these sequences allow for adding or deleting characters in the receive buffer to prevent buffer 
underflow/overflow due to small differences in the transmit/receive clock frequencies.

Sequence Length

Select from the drop down list the number of characters (subsequences) in the unique clock 
correction sequence.

The PCI EXPRESS example uses 

1

.

Rx Buffer Max Latency

Select from the drop down list the maximum number of characters to permit in the receive 
buffer before clock correction attempts to delete incoming clock correction sequences. Also 
determines the maximum latency of the receive buffer in RXUSRCLK cycles.

The PCI EXPRESS example uses 20.

Rx Buffer Min Latency

Select from the drop down list the minimum number of characters to permit in the receive 
buffer before clock correction attempts to add extra clock correction sequences to the receive 
buffer. Also determines the minimum latency of the receive buffer in RXUSRCLK cycles.

The PCI EXPRESS example uses 28.

Use Two Clock 
Correction Sequences

Activates the optional second Clock Correction sequence. Detection of either sequence 
triggers clock correction.

Содержание LogiCORE IP Spartan-6




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды