![background image](http://html2.mh-extra.com/html/xerox/versant-80-press/versant-80-press_customer-expectation-and-installation-manual_3327730019.webp)
Detailed Specifications
Xerox
®
Versant® 80 Press
Customer Expectation and Installation Guide
Xerox Confidential
14
1 Tray Oversized High Capacity Feeder (OHCF)
Capacity 2,000 sheets (using Centerline Paper)
Sizes
Min: 7.2 x 8.3 in (182 x 210 mm), w/postcard kit 4 x 6 in
(100 x 148 mm)
Max: 13 x 19.2 in (330 x 488 mm)
Weights
52 to 300 gsm
Supported
Media Types
Plain, uncoated, coated, transparencies, heavyweight,
predrilled, tabs, hole punched, labels, letterhead, postcard
(with Tray inserter)
Advanced High Capacity Feeder (Advanced HCF)
Capacity
2,000 sheets (per tray); combined capacity of 4,000
sheets (using Centerline Paper)
Sizes
Min: 7.2 x 7.2 in (182 x 182 mm), w/postcard kit 4 x 6 in
(100 x 148 mm)
Max: 13 x 19.2 in (330 x 488 mm)
Weights
52 to 350 gsm
Note: Optional performance for coated stocks is 64 –
350 gsm
Supported
Media Types
Plain, uncoated, coated, transparencies, heavyweight,
predrilled, tabs, hole punched, labels, letterhead, postcard
(with Tray inserter)
Finishing Specifications
Offset Catch Tray (OCT)
The Catch Tray holds a maximum of 500 sheets.
Catch Tray
Limitations
If utilizing the Catch Tray, overall productivity will decline if offsetting mode is selected. The print engine will pause printing to offset
between sets, and then resume. Productivity loss depends on the number of sheets per set, with single-page jobs representing the worst
case (approximately 50% productivity loss)
Sheets smaller than 6.7 inches (170 mm) in the cross-process direction (e.g. the feed edge) cannot be offset
Sheets larger than 11.7 inches (297 mm) in the cross-process direction (e.g. the feed edge) cannot be offset
With the EX-i/EX Fiery Print Server, the Offset Jobs box on the Finishing tab must be checked to enable offsetting.
Interface Module
TIP:
The Interface Module is required with any system configuration that has one or more finishing devices, except the Offset Catch Tray (OCT), BR Finisher and
BR Booklet Finisher.
The Interface Module acts as a paper path from the press to the finishing device; it also allows communication between the press and the finishing device. The
Interface Module also cools and decurls paper as it exits the press and before it enters the finishing device.
GBC AdvancedPunch
The GBC
AdvancedPunch is an inline die punch that uses modular die sets to Stack Tray Capacity: 8.5 x 11 inch (LTR) Dies enable a variety of hole punch patterns
in A4 or 8.5 x 11 inch (LTR), long-edge-fed media to support offline binding. The GBC AdvancedPunch is supported by all print servers. The GBC AdvancedPunch
requires an Interface Module as well as a High Capacity Stacker, Standard Finisher, Booklet Maker Finisher, or Standard Finisher Plus (and additional third-party
device).
GBC
AdvancedPunch
Specifications
Supports media from 75-216 gsm, coated and uncoated
ProClick die supports media from 75-203 gsm
Supports tab stock no wider than 9 in.; oversized tabs may be damaged
The GBC AdvancedPunch is able to bypass all coated and uncoated media sizes and weights that are printed on the Press
Requires an additional electrical receptacle; refer to the
Electrical Requirements for Optional Devices
GBC
AdvancedPunch
Limitations
GBC AdvancedPunch does not work in
conjunction with C/Z-fold or Standard Finisher punch, staple, or booklet making
Hole punch position from edge of paper is not adjustable
Preprinted Tabs cannot be punched
Opening the door of the GBC AdvancedPunch while the machine is running will cause the machine to jam and shut down
Gloss coated media may not run as reliably as uncoated paper. Typically, coated papers and high area coverage exhibit increased
variability in paper handling due to lower coefficients of friction, resulting in a broader distribution of punch registration and elevated
jam rates
Punching A4 or 8.5 x 11 in duplexed coated stocks using the GBC 3-hole punch (008R13072) is not recommended due to higher jam
rates
Stacking may be misaligned on jobs containing tab stock; these jobs will require additional jogging before final finishing
Due to the nature of punching holes, each punched sheet is slightly deformed, and when stacked, the edge with the holes will have an
increased height compared to the non-punched edge.
-
Reduced stack quality may be experienced due to variability in the punch hole formation
-
When sending output to the stack tray of the High Capacity Stacker, if this stack height difference exceeds one inch, the
machine will shut down and alert the operator to unload the stacker tray. This is done to prevent a jam and will result in a
reduction of stack capacity depending on the die being used
-
Using the HCS tray insert (shipped with your GBC unit) will increase stack capacity. See tables below for the expected stack
ranges of the HCS stack tray for each punch die
A4 and LTR punch units are not the same and A4 and LTR die sets are not interchangeable
-
LTR punch unit will be shipped with the 19-hole punch die
-
A4 unit will ship with the 21-hole punch die
-
Additional punch dies are available for order (see below)
-
Up to 3 additional die sets can be stored inside the GBC AdvancedPunch