Xerox Phaser 8860, Руководство по обслуживанию

Страница: 266 / 316

09/2007
6-46 Phaser 8860/8860MFP Service Manual
Fax Troubleshooting
Initial Issue Diagnostics
Fax Protocol Report
The Protocol Report provides transmission results, timing, and communications activity infor-
mation about each Fax transmission. Accessed from the System -> Information -> Trouble-
shooting -> FAX Problems menu, the Protocol Report provides Job Details similar to the
Transmission Report, and a detailed log of the communications activity between devices. Use
this report to diagnose possible communications errors between machines.
Table 1 lists the most common commands exchanged between Fax machines during a typical
transfer of data. When reviewing the Protocol Report, trace the exchange of commands to
identify irregularities. Commands in parentheses (_) may or may not appear in the log.
Fax Transmission Report
The Transmission Report provides transmission status and activity information about each Fax
transmission. Generation of this report is optional and is in an Error Only state by default. Use
the menus: System -> Job Defaults Setup -> Fax Defaults Setup -> Fax Send Setup to change
the Error Only default. Also by default, for the 8860MFP, the Transmission Report includes a
reduced image of the document scanned for faxing. Result codes appear in the Results box of
the Job Details section at the bottom of the page. The results format is <code><speed>. Where
code is one of the codes listed in
Table 2 . Speed is the transmission baud rate (i.e. 9600). Typ-
ically, the results are CP<speed> for a completed Fax. Fax failures (FA) may omit the speed if
the system was unable to start the connection. The job termination results (FA, TU, TS) count
as errors for the purpose of printing a Transmission Report.
In addition to the Results codes, the Job Details section includes Mode and Job Type codes.
Definitions of all these codes appears on each report.
Table 1 Common Fax Communication Commands
Command Definition Appropriate Responses
(NSF) (CSI) DIS Negotiating capabilities from a manual
receiver or an auto answer terminal (NSC) (CIG) DTC
(TSI) DCS
(NSF) (CSI) DIS
(CRP) (TSI) (NSS)
(PWD) (SEP) (CIG) DTC
(PWD) (SUB) (TSI) DCS
(NSC) (CIG) DTC
(PWD) (SEP) (CIG) DTC Mode setting from calling terminal
This is a poll operation (TSI) DCS
(NSF) (CSI) DIS
(CRP) (TSI) (NSS)
(TSI) DCS
(TSI) (NSS)
(PWD) (SUB) (TSI) DCS Mode setting from manual transmitter
or automatic receiver. CFR
FTT
(NSC) (CIG) DTC
(NSF) (CSI) DIS
(CRP)
CTC Mode setting from the transmitter to
the receiver. (CTR)
(CRP)
(EOR-NULL) Indicates the next block transmission
from the transmitter to the receiver. (ERR)
(RNR)
(CRP)
(EOR-MPS) or
(EOR-EOP) or
(EOR-EOM) or
(EOR-PRI-MPS) or
(EOR-PRI-EOP) or
(EOR-PRI-EOM) Indicate the next message transmis-
sion from the transmitter to the receiver (ERR)
(RNR)
PIN
(CRP)
MPS or EOP or EOM or
(PRI-MPS) or
(PRI-EOP) or
(PRI-EOM) Post-message commands MCF
RTP
RTN
PIP
PIN
(CRP)
(PPS-NULL) Post-message command for a partial
page: from the transmitter to the
receiver (PPR)
MCF
(RNR)
(CRP)
(PPS-MPS) or
(PPS-EOP) or(
PPS-EOM) or
(PPS-PRI-MPS) or
(PPS-PRI-EOP) or
(PPS-PRI-EOM) Post-message commands for a com-
plete page: from the transmitter to the
receiver (PPR)
MCF
(RNR)
PIP
PIN
(CRP)
(RR) Ask for the status of the receiver: from
the transmitter to the receiver (RNR)
(ERR)
MCF
PIP
PIN
(CRP)
DCN Phase E command None
Table 2 Fax Result Codes
Code Definition Description
FA Fax Failed The system was unable to connect to the Remote Station.
TU Terminated by user The transmission was canceled by the user.
TS Terminated by system The system ran out of resources. Typically, memory.
CP Completed The system was able to deliver the Fax.
Table 1 Common Fax Communication Commands
Command Definition Appropriate Responses