09/2007
4-24
Phaser 8860/8860MFP Service Manual
REP 2.0.3
Initial Issue
Repairs and Adjustments
5.
Install 1 (metal, hex-head) screw and washer at the rear position on the right-side to hold
the Drum Assembly and torque the screw to 25 in.-lbs.
6.
Install the remaining (metal, hex-head) screws into the bottom location (without a washer)
and the front location (with a washer and Ground Plate) on the right side of the Drum
Assembly and torque to 25 in.-lbs.
7.
Pull outward on the left Drum Assembly handle and the right chassis side to spread the
chassis and seat the left Drum bearing.
8.
Replace the Drum Temperature Sensor.
9.
Replace the Transfix Load Module, Ground Strap, and Preheater Lift Solenoid.
10. Align the clevis on the Transfix Load Arms with the holes in the mounting ears on the
Drum Assembly. The Transfix Load Arms should point in the opposite direction as the
Drum Thermistor. Position the Cam Followers on the Transfix Load Arms under the Trans-
fix Cams.
11. Insert the Clevis Pins through the clevis and the mounting ears on the Drum Assembly
(insert the pins from the outside). Check that the o-ring on each Clevis Pin is inside the
chassis.
12. Align the Exit Module to the chassis and re-route the Drum Temperature Sensor harness
through the opening provided. Seat the Exit Module in the chassis by first engaging the 2
front locating pins, and then the rear locating pins.
13. Inset and torque to 12 in-lbs. the 6 Exit Module screws. On 8860 models, the Exit Module
is secured with 4 screws torqued to 12 in-lbs.
NOTE:
After installing the Exit Module, perform the Wiper Alignment (
ADJ 2.5.1
). The
printer may report error 7,009.4x if the Wiper is misaligned.
Figure 4 8860MFP Exit Module Right Side Fasteners
Содержание Phaser 8860
