Xerox PHASER 3435 Скачать руководство пользователя | Manualshive

Страница: 219 / 247

background image

General Procedures and Information

Phaser 3435

5/08

6-33

Firmware Side is made up of

1. Network Interface Card is that relay the communication between Host and kernel using vari-

ous network protocol,

2. Kernel is that manages the flow control of emulation procedure, receiving data from Host or

Network card and printing with engine & rendering job,

3. Emulation is that interprets the various output data from selected emulation,
4. Engine is that prints rendered bit-map data to paper with required size and type by Kernel.
And then, for Job Spooling function for Multi-User, Multi-Printing that is occurred in Network print-
ing and various additional printing functions, this Kernel use max. 10 Queuing systems in a mem-
ory.

In Printing, the two procedures are

1. Case of using USB Port

•

After user start to print the wanted document to PCL string or compressed GDI bit-map
data, Driver translate the all graphic data of it and send data to host spooler. And then the
spooler sends the data stream to the printer via USB port.

•

Kernel receives this data from Host, and then select emulation fit to data and start
selected one. After emulation job end, Kernel sends the output bit-map data to Engine
using Printer Video Controller (by clock type for LSU).

•

Engine print the received data to required paper with the sequential developing process.

2. Case of using Network Interface Card

•

After user start to print the wanted document to PCL string or compressed GDI bit-map
data, Driver translate the all graphic data of it and send data to host spooler.

•

If so, Port monitor managing network port receives data from spooler and sends a data
stream to the Network Interface Card.

•

Network interface card receives it and send to Kernel part,

•

Kernel receives this data from Host, and then select emulation fit to data and start
selected one. After emulation job end, Kernel sends the output bit-map data to Engine
using Printer Video Controller (by clock type for LSU).

•

Engine print the received data to required paper with the sequential developing process.

The additional printing function are realized in

(1) Web environment
(2) Window environment.
On addition, Kernel informs a status of printing status and printer status to user made printing job
with the Status Monitor.

«
...
217
218
219
220
221
...
»

Содержание PHASER 3435
























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PHASER 3435

Бренд: Malyan Страницы: 9

870 - SuperScript B/W Laser Printer

Бренд: NEC Страницы: 52

SuperScript 1800

Бренд: NEC Страницы: 8

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 858

Panafax UF-7000

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 120

Бренд: Panasonic Страницы: 100

KX-MB781 - B/W Laser - All-in-One

Бренд: Panasonic Страницы: 96

Бренд: Panasonic Страницы: 130

Бренд: Oki Страницы: 210

Бренд: Panasonic Страницы: 77

Бренд: Panasonic Страницы: 402

Бренд: Panasonic Страницы: 54

Workio DP-8016P

Бренд: Panasonic Страницы: 88

Бренд: Panasonic Страницы: 60

Бренд: Xerox Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды