manualshive.com logo in svg

Xerox PHASER 3435, Руководство по обслуживанию

Принтер Xerox PHASER 3435 - мощное устройство для печати высокого качества. Спецификации включают в себя быструю скорость печати и большой объем памяти. Пользователи могут скачать бесплатное руководство по эксплуатации на manualshive.com. Удобно, просто и эффективно.

Поделиться
Скачать
background image

General Procedures and Information

6-30

5/08

Phaser 3435

engine informs the error status of the main system. And then the error message is dis-
played at LCD window or LED informing the error status of the user. 

•

Over Heat Error 

For overall engine state, if the temperature of the fixing unit is higher than the specified 
temperature and the temperature state is kept during the specified time, the engine 
defines Over Heat Error. When this error is broken out, the engine stops all functions and 
keeps it at the error state. Also, the engine informs the error status of the main system. 
And then the error message is displayed at LCD window or LED to inform the error status 
of the user. 

* To recover the heat error: The heat error recovery is operated automatically when the 
error is only caused by Low Heat Error, not the Heat Errors in Warm-up state and the Over 
Heat Error. If an error happens, then the engine memorizes a present temperature. In 
case of Low Heat Error, the maximum heat is supplied to the fixing unit. When a specified 
time is elapsed, the engine detects the temperature again. If the present temperature is 
higher than the memorized temperature, the error is recovered. In case of Over Heat 
Error, no heat is supplied to the fixing unit. When a specified time is elapsed, the engine 
detects a present temperature again. If the present temperature is a specified degree 
lower than the memorized temperature, the error is recovered. 

•

LSU

LSU receives the image data from PVC or HPVC and make the latent image on OPC sur-
face.
It uses the dual beam, LD1 and LD2. But the control method of them is the same.
Just in comparison with the single beam, the dual beam has the half of LSUs frequency.
->The frequency of the dual beam = the frequency of the single beam /2.

The errors related to LSU are as follows:
* By LReady: When the printing is started, the engine drives the polygon motor of LSU. 
After the specified time is elapsed, if the motor is not in a ready status, the engine detects 
the error that the polygon motor is not in a ready status. If this error happens, the engine 
stops all functions and keeps it at the error state. Also, the engine informs the error status 
of the main system and the error message is displayed at LCD window to inform the error 
status of the user. 

* By Hsync: When the polygon motor is ready, the LSU sends out the signal called Hsync 
and used to synchronize with each image line. So, if the engine does not detect consecu-
tively the signal for a fixed time, it defines the Hsync Error. If this error happens, the 
engine stops all functions and keeps it at the error state. Also, the engine informs the error 
status of the main system and then the error message is displayed at LCD window to 
inform the error status of the user. 

LSU Error Recovery: If the LReady or Hsync error happens, the paper exits out before 
hand. The engine mode is changed to recovery mode and the engine informs the main 
system of the engine mode. And the engine checks the LSU error. If the error doesn’t hap-
pen, the printing job will be proceeding. 

Содержание PHASER 3435
























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PHASER 3435

Oki C910 Hardware preview
C910
Бренд: Oki Страницы: 2
Oki C910 Material Safety Data Sheet preview
C910
Бренд: Oki Страницы: 52
Oki C110 Manual Do Usuário preview
C110
Бренд: Oki Страницы: 117
Oki C110 How To Remove Jammed Paper preview
C110
Бренд: Oki Страницы: 45
Oki C110 Manual De L'Utilisateur preview
C110
Бренд: Oki Страницы: 112
Oki C110 Guías Del Usuario Manual preview
C110
Бренд: Oki Страницы: 115
Oki C110 Quick Setup preview
C110
Бренд: Oki Страницы: 2
Xerox 4050 Product Reference preview
4050
Бренд: Xerox Страницы: 68
Xerox 460 Installation And Troubleshooting Manual preview
460
Бренд: Xerox Страницы: 210
Samsung SPP 2020 - Photo Printer - 20 Sheets Manual Del Usuario preview
SPP 2020 - Photo Printer - 20 Sheets
Бренд: Samsung Страницы: 81
Samsung ML-6000 Bedienungsanleitung preview
ML-6000
Бренд: Samsung Страницы: 98
Samsung ML-4050N Compatibility Manual preview
ML-4050N
Бренд: Samsung Страницы: 6
Samsung ML-3750ND User Manual preview
ML-3750ND
Бренд: Samsung Страницы: 203
Samsung ML-3312ND Manual Del Usuario preview
ML-3312ND
Бренд: Samsung Страницы: 264
Samsung ML-2165W/XAA Manual Del Usuario preview
ML-2165W/XAA
Бренд: Samsung Страницы: 228
Samsung ML-2165 User Manual preview
ML-2165
Бренд: Samsung Страницы: 211
Samsung ML-2525 Brochure & Specs preview
ML-2525
Бренд: Samsung Страницы: 5
Samsung ML-1865W Manual Del Usuario preview
ML-1865W
Бренд: Samsung Страницы: 92

Бренды по названию

Популярные бренды

Загрузить еще бренды