Xerox PHASER 3435 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 247

background image

Introduction

Phaser 3435

5/08

v

2. The machine contains many rollers, gears and fans. Take great care to ensure that you do

not catch your fingers, hair or clothing in any of these rotating devices.

3. Do not place any small metal objects, containers of water, chemicals or other liquids close to

the machine which if spilled could get into the machine and cause damage or a shock or fire
hazard.

4. Do not install the machine in areas with high dust or moisture levels, beside an open window

or close to a humidifier or heater. Damage could be caused to the machine in such areas.

5. Do not place candles, burning cigarettes, etc. on the machine, these could cause a fire.
6. The fuser unit works at a high temperature. Use caution when working on the machine. Wait

for the fuser to cool down before disassembly.

Assembly / Disassembly Precautions

Replace parts carefully, always use Xerox parts. Take care to note the exact location of parts and
also cable routing before dismantling any part of the machine. Ensure all parts and cables are re-
placed correctly.
Please carry out the following procedures before dismantling the machine or replacing any parts.
1. Check the contents of the machine memory and make a note of any user settings. These will

be erased if the mainboard is replaced.

2. Ensure that power is disconnected before servicing or replacing any electrical parts.
3. Disconnect printer interface cables and power cables.
4. Be sure to remove the print cartridge before you disassemble any parts.
5. Only use approved spare parts. Ensure that part number, product name, any voltage, current

or temperature rating are correct.

6. When removing or re-fitting any parts do not use excessive force, especially when fitting

screws into plastic.

7. Take care not to drop any small parts into the machine.
8. Handling of the OPC Drum

- The OPC Drum can be irreparably damaged if it exposed to light.
Take care not to expose the OPC Drum either to direct sunlight or to fluorescent or incandes-
cent room lighting. Exposure for as little as 5 minutes can damage the surface’s photocon-
ductive properties and will result in print quality degradation. Take extra care when servicing
the machine. Remove the OPC Drum and store it in a black bag or other lightproof container.
Take care when working with the covers (especially the top cover) open as light is admitted to
the OPC area and can damage the OPC Drum.
- Take care not to scratch the green surface of OPC Drum Unit.
If the green surface of the Drum Cartridge is scratched or touched the print quality will be
compromised.

«
...
5
6
7
8
9
...
»

Содержание PHASER 3435
























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PHASER 3435

Power Defense PD3

Бренд: Eaton Страницы: 4

DocuPrint 4850 NPS

Бренд: Xerox Страницы: 276

Бренд: Afinia 3D Страницы: 47

Бренд: Oki Страницы: 2

Бренд: Olivetti Страницы: 24

Бренд: TRENDnet Страницы: 14

Pro-LX Pro-LX Laminating Card...

Бренд: FARGO electronics Страницы: 228

Бренд: StarTech.com Страницы: 13

Бренд: CNET Страницы: 2

LaserPro X500 III-80Y

Бренд: GCC Technologies Страницы: 127

Бренд: Z Corporation Страницы: 127

Бренд: Avery Weigh-Tronix Страницы: 40

Бренд: Olivetti Страницы: 315

Expression EcoTank ET-3600

Бренд: Epson Страницы: 202

Expression Home XP-200

Бренд: Epson Страницы: 185

ActionPrinter 3250 - ActionPrinter-3250 Impact Printer

Бренд: Epson Страницы: 22

ActionPrinter 4000

Бренд: Epson Страницы: 2

ActionPrinter 3260 s

Бренд: Epson Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды