Management tools
_ 47
Opening the Troubleshooting Guide
Find solutions for problems by using the
Troubleshooting Guide
.
Double click the Status Monitor icon on the Windows task bar.
Or, from the
Start
menu, select
Programs
or
All Programs
>
your printer
driver name
>
Troubleshooting Guide
.
USING SETIP PROGRAM (PHASER 3160N ONLY)
This program is for the network IP setting using the MAC address which is
the hardware serial number of the network printer card or interface.
It is especially for the network administrator to set several network IPs at the
same time.
•
TCP/IPv6 is not supported by this program.
•
You can only use the SetIP program when your machine is
connected to a network.
Windows
The following procedure is based on the Windows XP operating system.
Installing the program
1.
Make sure that the machine is connected to your computer and
powered on.
2.
Insert the supplied software CD into your CD-ROM drive.
•
The software CD should automatically run and an installation
window appear.
•
If the installation window does not appear, click
Start
and then
Run
. Type X:\
Setup.exe
, replacing “X” with the letter which
represents your drive. Click
OK
.
•
If you use Windows Vista, click
Start
>
All programs
>
Accessories
>
Run
.
Type X:\
Setup.exe
replacing “X” with the letter which represents
your drive and click
OK
.
•
If the
AutoPlay
window appears in Windows Vista, click
Run
Setup.exe
in
Install or run program
field, and click
Continue
in
the
User Account Control
windows.
3.
Click
Install SetIP Utility(Optional)
.
4.
Click
Next
>
Next
.
5.
Click
Finish
.
Printing out the machine’s MAC address
In ready mode, press and hold the (cancel button) for about
7
seconds. You can find your machine’s MAC address and IP address.
Setting network values
1.
Print the machine’s network configuration report to find your
machine’s MAC address.
2.
From the Windows
Start
menu, select
All Programs
>
SetIP
>
SetIP
.
3.
Click to open the TCP/IP configuration window.
4.
Enter the network card’s MAC address, IP address, subnet mask,
default gateway, and then click
Apply
.
When you enter the MAC address, enter it without a colon(:).
5.
The machine prints the network configuration report. Confirm all the
settings are correct.
6.
Close the SetIP program.
Macintosh
SetIP program should be automatically installed during the printer driver
installation.
Printing out the machine’s MAC address
In ready mode, press and hold the (cancel button) for about
7
seconds. You can find your machine’s MAC address and IP address.
Setting network values
If you want to change your network printer IP setting, follow the below
instruction.
If you select
Typical installation for a network printer
during the
printer driver installation, the SetIP program automatically runs
after the installation. Go to step 4.
1.
Print the machine’s network configuration report to find your
machine’s MAC address.
2.
Open the
Library
folder >
Printers
>
Xerox
>
your printer model
name
>
SetIP
.
3.
Double click the
SetIPApplet.html
file.
4.
The certificate window appears, click
Trust
.
5.
Click to open the TCP/IP configuration window.
6.
Enter the network card’s MAC address, IP address, subnet mask,
default gateway, and then click
Apply
.
When you enter the MAC address, enter it without a colon(:).
7.
The machine prints the network configuration report. Confirm all the
settings are correct.
8.
Close the SetIP program.
Linux
SetIP program should be automatically installed during the printer driver
installation.
Printing out the machine’s MAC address
In ready mode, press and hold the (cancel button) for about
7
seconds. You can find your machine’s MAC address and IP address.
Setting network values
1.
Print the machine’s network configuration report to find your
machine’s MAC address.
2.
Open the /
opt
/
Xerox
/
mfp
/
share
/
utils
/.
3.
Double click the
SetIPApplet.html
file.
4.
Click to open the TCP/IP configuration window.
5.
Enter the network card’s MAC address, IP address, subnet mask,
default gateway, and then click
Apply
.
When you enter the MAC address, enter it without a colon(:).
6.
The machine prints the network configuration report. Confirm all the
settings are correct.
7.
Close the SetIP program.
Содержание Phaser 3160B
Страница 1: ......
Страница 6: ...table of contents Table of contents_ 6 GLOSSARY 67 ...
Страница 71: ...Glossary_ 71 ...