Xerox Phaser 3160B, Руководство пользователя, Страница: 27 / 73

Network Setup (Phaser 3160N only) _ 27
c) Double-click CD-ROM icon that appears on your Macintosh
desktop.
d) Double-click the MAC_Installer folder.
e) Double-click the Installer OS X icon.
f) Enter the password and click OK .
g) The Xerox Installer window opens. Click Continue .
h) Select Uninstall and click Uninstall .
i) When the message which warns that all applications will close
on your computer appears, Click Continue .
j) When the uninstall is done, click Quit .
Linux
1. Make sure that the machine is connected to your network and powered
on. Also, your machine’s IP address should have been set.
2. Insert the supplied software CD into your CD-ROM drive.
3. Double-click CD-ROM icon that appears on your Linux desktop.
4. Double-click the Linux folder.
5. Double-click the install.sh icon.
6. The Xerox Installer window opens. Click Continue .
7. The Add printer wizard window opens. Click Next .
8. Select Network printer and click Search button.
9. The Printer’s IP address and model name appears on list field.
10. Select your machine and click Next .
USING A WIRED NETWORK
You must set up the network protocols on your machine to use it on your
network. This chapter will show you how this is easily accomplished.
You can use network after connecting network cable to a corresponding
port on your machine.
Printing network configuration report
You can print a Network Configuration Report from the machine's control
panel that will show the current machine’s network settings. This will help
you to set up a network and troubleshooting problems.
To print the report:
In ready mode, press and hold the (cancel button) for about
7
seconds.
You can find your machine’s MAC address and IP address.
For example:
• IP Address : 192.0.0.192
Setting IP address
First, set up an IP address for network printing and managements. In most
cases a new IP address will be automatically assigned by a DHCP
(Dynamic Host Configuration Protocol) server located on the network.
In a few situations the IP address must be set manually. This is called a
static IP and is often required in corporate Intranets for security reasons.
• DHCP IP assignment : Connect your machine to the network, connect
the power cord and wait a few minutes for the DHCP server to assign an
IP address to the machine. Then, print the Network Configuration
Report as explained above. If the report shows that the IP address has
changed, the assignment was successful. You will see the new IP
address in the report.
• Static IP assignment : Use SetIP program to change the IP address
from your computer. (Only if you do not want to use DHCP.)
In an office environment, we recommend that you contact a network
administrator to set this address for you.
IP setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your
machine using its MAC address to communicate with the machine. A
MAC address is the hardware serial number of the network interface and
can be found in the Network Configuration Report .
For using SetIP program, disable the computer firewall before continuing
by performing the following:
1. Open Start > All programs > Control Panel .
2. Double click Security Center .
3. Click Windows Firewall at the bottom of the screen.
4. Disable the firewall.
Installing the program
1. Make sure that the machine is connected to your computer and
powered on.
2. Insert the supplied software CD into your CD-ROM drive.
• The software CD should automatically run and an installation
window appear.
• If the installation window does not appear, click Start and then
Run . Type X:\ Setup.exe , replacing “X” with the letter which
represents your drive. Click OK .
• If you use Windows Vista, click Start > All programs >
Accessories > Run .
Type X:\ Setup.exe replacing “X” with the letter which represents
your drive and click OK .
• If the AutoPlay window appears in Windows Vista, click Run
Setup.exe in Install or run program field, and click Continue in
the User Account Control windows.
3. Click Install SetIP Utility(Optional) .
4. Click Next > Next .
5. Click Finish .
Starting the program
1. Connect your machine to the network with a network cable.
2. Turned on the machine.
3. From the Windows Start menu, select All Programs > your printer
driver name > SetIP > SetIP .
4. Click on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5. Enter the machine’s new information into the configuration window
as follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.