Network Setup (Phaser 3160N only)
_ 28
•
MAC Address
: Find the machine’s MAC address from the
Network Configuration Report
and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
•
IP Address
: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150,
enter 192.168.1.X. (X is number between 1 and 254 other than
the computer’s address.)
•
Subnet Mask
: Enter a Subnet Mask.
•
Default Gateway
: Enter a Default Gateway.
6.
Click
Apply
, and then click
OK
. The machine will automatically print
the
Network Configuration Report
. Confirm that all the settings are
correct.
7.
Click
Exit
to close the SetIP program.
8.
If necessary, restart the computer’s firewall.
IP setting using SetIP Program (Macintosh)
For using SetIP program, disable the computer firewall before continuing
by performing the following:
1.
Open
System Preferences
.
2.
Click
Security
.
3.
Click the
Firewall
menu.
4.
Turn firewall off.
The following instructions may vary for your model.
1.
Connect your machine to the network with a network cable.
2.
Insert the Installation CD-ROM, and open the disk window, select
MAC_Installer
>
MAC_Printer
>
SetIP
>
SetIPapplet.html
.
3.
Double click the file and
Safari
will automatically open, then select
Trust
. The browser will open the
SetIPapplet.html
page that shows
the printer’s name and IP address information.
4.
Click on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5.
Enter the machine’s new information into the configuration window
as follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
•
MAC Address
: Find the machine’s MAC address from the
Network Configuration Report
and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
•
IP Address
: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150,
enter 192.168.1.X. (X is number between 1 and 254 other than
the computer’s address.)
•
Subnet Mask
: Enter a Subnet Mask.
•
Default Gateway
: Enter a Default Gateway.
6.
Select
Apply
, then
OK
, and
OK
again. The printer will automatically
print the configuration report. Confirm that all the settings are correct.
Quit Safari
. You may close and eject the installation CD-ROM. If
necessary, restart the computer’s firewall. You have successfully
changed the IP address, subnet mask, and gateway.
IP setting using SetIP Program (Linux)
SetIP program should be automatically installed during the printer driver
installation.
1.
Print the machine’s network configuration report to find your
machine’s MAC address.
2.
Open the /
opt
/
Xerox
/
mfp
/
share
/
utils
/.
3.
Double click the
SetIPApplet.html
file.
4.
Click to open the TCP/IP configuration window.
5.
Enter the network card’s MAC address, IP address, subnet mask,
default gateway, and then click
Apply
.
When you enter the MAC address, enter it without a colon(:).
6.
The machine prints the network configuration report. Confirm all the
settings are correct.
7.
Close the SetIP program.
Network parameter setting
You can also set up the various network settings through the network
administration programs such as
CentreWare IS
.
Restoring factory default settings
You may need to reset the machine to the factory default settings when
machine that you are using is connected to new network environment.
Restoring factory default settings using CentreWare IS
1.
Start a web browser such as Internet Explorer, Safari or Firefox and
enter your machine’s new IP address in the browser window.
For example,
2.
When the
CentreWare IS
window opens, click
Properties
>
General
.
3.
Click
Reset
. Then, click on the button below to restroe defaults.
4.
Turn off and restart machine to apply settings.
Содержание Phaser 3160B
Страница 1: ......
Страница 6: ...table of contents Table of contents_ 6 GLOSSARY 67 ...
Страница 71: ...Glossary_ 71 ...