Xerox DFC155 Скачать руководство пользователя

Страница: 97 / 151

602E52970

7-1

7.1 MAINTENANCE

The facsimile machine's maintenance includes

periodic preventive procedures

(such as optical unit cleaning), and

action to be taken following a message

on the

display (such as the ink out message): the procedures are normally carried out by the

user so they will be described in detail in the User Guide. Here only a brief description

is provided.

7.1.1 OUT OF INK Message

The facsimile machine has a built-in counter for keeping track of ink consumption,

so as to provide an ink out message at the right time. When the ink present in the

cartridge runs out, the display shows the following message:

OUT OF INK

to prompt the operator to:

- replace the

ink cartridge

, if the print head is of the

rechargeable

type

- replace the

entire print head

, if it is of the

disposable

type.

If a rechargeable print head is used, the ink cartridge can be replaced several times.

When a deterioration in the printing quality is observed, after several replacements,

this means that the entire print head is to be replaced.

While replacing the

cartridge only

, but not the entire print head, a little ink may be

ejected, to prevent the printing area from getting dirty, when the out of ink message

appears,

a sheet of paper is automatically inserted

under the print carriage.

7. MAINTENANCE AND REPLACEMENT

PROCEDURES

Содержание DFC155
























































































































































Результаты поиска

Содержание DFC155

Отзывы:

Похожие инструкции для DFC155

Бренды по названию

Популярные бренды

Xerox DFC155, Руководство по обслуживанию и список запасных частей

Результаты поиска

Содержание DFC155

Отзывы:

Похожие инструкции для DFC155

Бренды по названию

Популярные бренды