Xerox DFC155 Скачать руководство пользователя

Страница: 98 / 151

7-2

602E52970

7.1.2 Replacing the rechargeable Ink Cartridge

1. Tilt the printer cover.
2. Remove the used cartridge,

without removing the print head

, by pressing the

catch.

3. Remove the new cartridge from its sealed packing and peel the protective film off

the ink supply hole.

4.Insert the cartridge in its housing immediately and press it in until the catch clicks

into place to indicate that the cartridge is correctly inserted.

5.Close the printer cover: if the

head cleaning

feature is enabled (bit 2 of software

parameter SW09 =1, see section 4.1), the facsimile machine automatically starts

the

nozzle cleaning and testing procedure

(see section 3.1.5, step 7). If it is not,

the sheet of paper is unloaded.

WARNING

Do not touch the inked area!

7.1.3 Replacing the Print Head

See section 3.1.5 (starting from step 4).

7.1.4 Cleaning the Print Head

If print quality deteriorates, the print nozzles need to be tested first (see sect. 6.1.2)

to determine whether it is necessary to perform the print head CLEARING procedure,

which entails drawing ink to free the print head from any air bubbles it may contain.

HEAD MAINTENANCE

(F)/

AUTOMATIC RX

09-05-95 14:58

Setting

1) The facsimile machine is in stand-by mode

2) Access the main menu and select the HEAD MAINTE-

NANCE submenu of the FAX SETUP menu

3) Press twice to start procedure.

Display

PRINTING

Содержание DFC155
























































































































































Результаты поиска

Содержание DFC155

Отзывы:

Похожие инструкции для DFC155

Бренды по названию

Популярные бренды

Xerox DFC155, Руководство по обслуживанию и список запасных частей

Результаты поиска

Содержание DFC155

Отзывы:

Похожие инструкции для DFC155

Бренды по названию

Популярные бренды