Installation Procedure
35
In
s
tal
la
tio
n
W
h
e
n
Us
ing
T
C
P/
IP
(LPD
/
6) Select [Enabled] then select [Save].
7) Select [Close] repeatedly until the [Network Settings] screen is displayed.
3
Set an IP address.
If an IP address is already set, this step is not necessary. Also, in an environment with
DHCP or BOOTP, configure the way to obtain an IP address. Either the address
cannot be obtained automatically or manual configuration is preferred, configure an IP
address, a subnet mask, and a gateway address.
1) Select [Protocol Settings].
2) Select [TCP/IP - Get IP Address] and then select [Change Settings].
3) Select one from [DHCP], [BOOTP], [RARP], [DHCP/Autonet] or [Manual]. If you
select anything other than [Manual], proceed to step 4.
Note
• When using a DHCP server, also configure the WINS (Windows Internet Name Service)
server.
4) Select [TCP/IP - IP Address] and select [Change Settings].
5) Select [TCP/IP - Get IP Address] and then select [Change Settings].
Note
• Enter address in the format “xxx.xxx.xxx.xxx”. The "xxx" should be a numeric value in the
range from 0 to 255. However, 224 or 225.xxx.xxx.xxx and 127.xxx.xxx.xxx cannot be used.
• When you make an entry mistake, press the <O> (clear) button and enter again.
• When you would like to move to the next value without entering all 3 digits, select [save/
select next].
6) Select [Save].
7) Configure [TCP/IP - Subnet Mask] and [TCP/IP - Gateway Address] as the above.
Note
• Enter address in the format “xxx.xxx.xxx.xxx”. The "xxx" should be a numeric value in the
range from 0 to 255. However, 224 or 225.xxx.xxx.xxx and 127.xxx.xxx.xxx cannot be used.
• Specify the subnet mask by a combination of the numbers 0, 128, 192, 224, 240, 248, 252,
254, and 255. However, you cannot use 0 between non-zero values.
• If you do not want to set the gateway address, enter "0.0.0.0".
4
Select [Close] repeatedly until the [System Settings] screen is displayed.
5
Select [Exit].
6
After the machine is restarted, print out a settings list to confirm that the LPD or
Port9100 port is enabled and TCP/IP is configured.
For information how to print a setting list, refer to “Print Report/List” in Chapter 12 of the User Guide.
Configure other LPD settings as necessary. Refer to "LPD" (P.66) for the LPD configuration. Also if
using Port 9100, configure the Port9100 as necessary. Refer to "Port9100" (P.69) for the Port9100
configuration.
Configuration on the Computer
The following describes the configuration procedure for the computer.
In order to print from the machine, the computer needs to have a print driver installed.
For information about the supported operating systems, refer to "Supported Operating Systems" (P.16).
For information about the driver installation procedure, refer to the manual contained in the CentreWare
Utilities OD-ROM.
You can also print from a Macintosh using TOP/IP (LPD). You will need an optional PostScript3 kit.
Refer to the manual contained in the CD-ROM provided with the machine for the print driver
installation procedure.
Содержание ApeosPort C6550 I
