Configuration of the Job Flow
105
U
s
in
g Sc
an
S
e
rv
ic
e
4) Select [SOAP] and then select [Change Settings].
5) Select [Port Status] and select [Change Settings].
6) Select [Enabled] then select [Save].
7) Select [Exit].
3
Enable the SNMP port.
1) Select [Network Settings].
2) Select [Port Settings].
3) Select [SNMP] and then select [Change Settings].
4) Select [Port Status] and select [Change Settings].
5) Select [Enabled] then select [Save].
6) Select [Exit].
7) Enable the Internet service (HTTP) port as above.
8) Select [Close] repeatedly until the [Network Settings] screen is displayed.
4
Set an IP address.
If an IP address is already set, this step is not necessary. Also, in an environment with
DHCP or BOOTP, configure the way to obtain an IP address. Either the address
cannot be obtained automatically or manual configuration is preferred, configure an IP
address, a subnet mask, and a gateway address.
1) Select [Protocol Settings].
2) Select [TCP/IP - Get IP Address] and then select [Change Settings].
3) Select one from [DHCP], [BOOTP], [RARP], [DHCP/Autonet] or [Manual]. If you
select anything other than [Manual], proceed to step 5.
Note
• When using a DHCP server, also configure the WINS (Windows Internet Name Service)
server.
4) When [Manual] is selected, select [TCP/IP - IP Address] then [Change Settings].
5) Select [TCP/IP - IP Address] and select [Change Settings].
6) Select [TCP/IP - Get IP Address] and then select [Change Settings].
Note
• Enter the address in the format “xxx.xxx.xxx.xxx”. The "xxx" should be a numeric value in the
range from 0 to 255. However, 224 or 225.xxx.xxx.xxx and 127.xxx.xxx.xxx cannot be used.
• When you make an entry mistake, press the <C> (Clear) button and enter again.
• When moving to the next value without entering all 3 digits, select [save/select next].
7) Select [Save].
8) Configure [TCP/IP - Subnet Mask] and [TCP/IP - Gateway Address] as the above.
Note
• Enter the address in the format “xxx.xxx.xxx.xxx”. The "xxx" should be a numeric value in the
range from 0 to 255. However, 224 or 225.xxx.xxx.xxx and 127.xxx.xxx.xxx cannot be used.
• Specify the subnet mask by a combination of the numbers 0, 128, 192, 224, 240, 248, 252,
254, and 255. However, you cannot use 0 between non-zero values.
• If you do not set the gateway address, enter "0.0.0.0".
5
Select [Close] repeatedly until the [System Settings] screen is displayed.
6
Select [Exit].
7
After the machine is restarted, print out a settings list to confirm that the SOAP, SNMP
port and the Internet service (HTTP) port are enabled and the IP addresses are
configured.
For information how to print a setting list, refer to “Print Report/List” in Chapter 12 of the User Guide.
Содержание ApeosPort C6550 I
