![background image](http://html1.mh-extra.com/html/xerox/apeosport-350-i/apeosport-350-i_network-administration-manual_885189049.webp)
Installation Procedure
47
Installation When Using
TCP/IP
(LPD/Port
5
3
Set an IP address.
If an IP address is already set, this step is not necessary. Also, in an environment with
DHCP or BOOTP, configure the way to obtain an IP address. Either the address
cannot be obtained automatically or manual configuration is preferred, configure an IP
address, a subnet mask, and a gateway address.
1) Select [Protocol Settings].
2) Select [TCP/IP - Get IP Address] and then select [Change Settings].
3) Select one from [DHCP], [BOOTP], [RARP], [DHCP/Autonet] or [Manual] and then
select [Save]. If you select anything other than [Manual], proceed to Step 4.
Note
•
When using a DHCP server, also configure the WINS (Windows Internet Name Service)
server.
4) Select [TCP/IP - IP Address] and select [Change Settings].
5) Enter the IP address using the numeric keypad.
Note
•
Enter address in the format “xxx.xxx.xxx.xxx”. The "xxx" should be a numeric value in the
range from 0 to 255. However, 224 or 225.xxx.xxx.xxx and 127.xxx.xxx.xxx cannot be used.
•
When you make an entry mistake, press the <C> (clear) button and enter again.
•
When you want to move to the next value without entering all 3 digits, select [save/select
next].
6) Select [Save].
7) Configure [TCP/IP - Subnet Mask] and [TCP/IP - Gateway Address] as the above.
Note
•
Enter address in the format “xxx.xxx.xxx.xxx”. The "xxx" should be a numeric value in the
range from 0 to 255. However, 224 or 225.xxx.xxx.xxx and 127.xxx.xxx.xxx cannot be used.
•
Specify the subnet mask by a combination of the numbers 0, 128, 192, 224, 240, 248, 252,
254, and 255. However, you cannot use 0 between non-zero values.
•
If you do not want to set the gateway address, enter "0.0.0.0".
4
Select [Close] repeatedly until the [System Settings] screen is displayed.
5
Select [Exit].
6
After the machine is restarted, print out a settings list to confirm that the LPD or Port
9100 port is enabled and TCP/IP is configured.
For information on how to print a settings list, refer to "Print Report/List" under "Chapter 13 Machine
Status" in the User Guide.
Configure other LPD settings as necessary. Refer to "LPD" (P.79) for the LPD configuration. Also if
using Port 9100, configure the Port 9100 as necessary. Refer to "Port 9100" (P.82) for the Port 9100
configuration.
Configuration on the Computer
The following describes the configuration procedure for the computer.
In order to print from the machine, the computer needs to have a print driver installed.
For information on the supported operating systems, refer to "Supported Operating Systems" (P.19).
For information on the driver installation procedure, refer to the manual contained in the CentreWare
Utilities OD-ROM.
You can also print from a Macintosh using TOP/IP (LPD). You will need an optional PostScript 3 Kit.
Refer to the manual contained in the CD-ROM provided with the kit for the print driver installation
procedure.
Содержание apeosport 350 I
