Xerox 1235/DX - Phaser Color Laser Printer Скачать руководство пользователя страница 107

Страница: 107 / 144

Advanced Features and Troubleshooting Manual

Troubleshooting

B8-Duplex Jam

Fault

Paper did not enter the duplex module properly,

causing a paper jam. Open Cover B and refer to the

labels on the printer to clear the jam.

B13-Duplex Inverter Jam

Fault

Paper did not exit the duplex module correctly,

causing a paper jam. Open Area B and refer to the

labels on the printer to clear the jam.

B21-Duplex Area Jam

Fault

Paper did not exit the transport area correctly,

causing a paper jam. Open Cover B and refer to the

labels on the printer to clear the jam.

-Check Tray

[C1-Check Tray 1]
[C2-Check Tray 2]
[C3-Check Tray 3]

Fault

The tray is not installed. Make sure the tray is

fully inserted.

-Tray Misfeed

[E1-Tray 1 Misfeed]
[E2-Tray 2 Misfeed]
[E3-Tray 3 Misfeed]

Fault

Paper did not exit the tray properly, causing a

paper jam. Pull out the tray, retrieve and discard

the misfed paper and reinsert the tray. Open Cover

B to search for additional paper. Cover B must be

opened to clear the misfeed message on the front

panel.

E9-Top Cover A Open

Fault

The top cover (Cover A) is open. Close the cover

so that printing can continue.

E12-Output Bin Full, Top

Fault

The top (face-down) bin is full and cannot accept

any more prints until it is emptied. Once emptied,

printing will continue where it left off.

E14-Front Cover B Open

Fault

The front cover (Cover B) is open. Close the cover

so that printing can continue.

-Drum Missing

[EA-Black Drum Missing]
[EB-Cyan Drum Missing]
[EC-Magenta Drum
Missing]
[ED-Yellow Drum Missing]

Fault

The imaging drum is either missing or requires

reseating to be recognized by the printer. Turn off

the printer, make sure the imaging drum is

properly installed and turn on the printer. If the

problem persists, install a new imaging drum. For

further assistance, check the support links at

www.xerox.com/officeprinting/1235support

Printer Management Status Messages (cont'd.)

Message

Type

Explanation/Corrective Action

Содержание 1235/DX - Phaser Color Laser Printer

















































































































































Результаты поиска

Содержание 1235/DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 1235/DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды

Xerox 1235/DX - Phaser Color Laser Printer, Руководство по расширенным функциям и устранению неисправностей

Результаты поиска

Содержание 1235/DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 1235/DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды