Xantrex XKW 12-150 Скачать руководство пользователя | Manualshive

Страница: 74 / 90

background image

Operation

Remote Monitoring of Readback Signals and Status Indicators

72

Operating Manual for XKW 3kW Series Power Supply

Remote Monitoring of Readback Signals and Status Indicators

Readback

Signals

Calibrated readback signals for remote monitoring of the output voltage and current
are available via connections at the J3 connector on the rear panel. Internal switch
SW1 settings allow you to select either a 0-5Vdc or a 0-10Vdc range for the output.
See

“Configuring for Remote Programming, Sensing, and Monitoring” on page 48

for more information about making these connections.

Table 3.5

shows the required pin connections and switch settings for remote

monitoring of readback signals with 0-5Vdc or 0-10Vdc outputs. Use
shielded-twisted pair wiring (20 to 24 AWG) and ground the shield to J3 connector
pin 6 or to the chassis via one of the J3 connector screws.

Table 3.5

Supply Settings for Remote Monitoring of Readback Signals

The readback signal represents 0 to 100% of the model-rated output.

Status

Indicators

Status indicators for thermal shutdown, OVP circuit, programming mode, and
operating mode are available via connections on the J3 connector on the rear panel.

Table 3.6

shows the indicator signals, the J3 connector pin at which they are

available, an approximation of the signal magnitude, and the source impedance
through which the signal is fed. Use 20 to 24 AWG wiring.

Table 3.6

Power Supply Settings for Status Indicator Signals

Readback Signal

J3 Connections:

Switch SW1 Settings:

Output Signal
Range

Signal (+)

Return (-)

Switch #

Setting

Output Voltage

Pin 19

Pin 12

SW1-4

CLOSED
OPEN

0-5Vdc
0-10Vdc

Output Current

Pin 7

Pin 12

SW1-3

CLOSED
OPEN

0-5Vdc
0-10Vdc

Indicator Signal/Alternate State

J3 Connections:

Signal
Voltage

Source
Impedance

Signal (+) Return (-)

Thermal Shutdown/
Normal Operation

Pin 18
Pin 18

Pin 6
Pin 6

+13V
0V

1k ohms
1k ohms

OVP Circuit Activated/
OVP Circuit Not Activated

Pin 17
Pin 17

Pin 6
Pin 6

+13V
-13V

1k ohms
1k ohms

Remote Programming Mode/
Local Programming Mode

Pin 4
Pin 4

Pin 6
Pin 6

+13V
0V

1k ohms
1k ohm

Voltage Mode Operation/
Current Mode Operation

Pin 5
Pin 5

Pin 6
Pin 6

+13V
-13V

1k ohms
1k ohms

TM-25OP-01XN.book Page 72 Monday, April 5, 2004 8:58 AM

«
...
72
73
74
75
76
...
»

Содержание XKW 12-150



























































































Отзывы:

Нет отзывов

Похожие инструкции для XKW 12-150

Бренд: Makita Страницы: 6

Бренд: Makita Страницы: 14

Бренд: Makita Страницы: 7

Бренд: Makita Страницы: 13

Бренд: Makita Страницы: 4

Бренд: Makita Страницы: 5

Бренд: Makita Страницы: 17

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 12

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 3

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды