Xantrex Xantrex PRO XM 1000 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 77

background image

Installation

3–22

975-0263-01-01

Testing in Invert Mode

To test the XM Series Inverter in invert mode:

1. For hardwired installations, ensure shore power is not present.

2. Press the on/off button to turn the inverter on.

The status LED on the display panel glows yellow and the LED display
illuminates.

3. Plug an appliance within the power rating of the inverter into the XM

Series Inverter GFCI or an AC outlet hardwired to the XM Series
Inverter.

4. Turn the appliance on to verify that it operates.

If the appliance operates, your installation is successful. If your installation
has AC input and output hardwired to the XM Series Inverter, proceed to
“Testing in Shore Power Mode”.

If the status LED on the display panel glows red, see the Troubleshooting
chapter.

Testing in Shore Power Mode

To test the XM Series Inverter in shore power mode:

u

With the appliance from the previous test still connected and operating,
connect the shore power source.

The XM Series Inverter transfers the appliances to shore power. The
status LED on the display panel glows green.

If the appliance operates, your installation is successful.

Note:

If the on/off button on the XM Series Inverter is on, the XM Series

Inverter will automatically supply the appliances with inverter power if the shore
power source fails or becomes disconnected.
If the on/off button on the XM Series Inverter is on and shore power voltage is too
low (less than 90 volts AC), the unit will transfer to inverter power to continue
running your appliances.

Note:

Whether or not the on/off button is on, shore power will pass through the

XM Series Inverter.

«
...
39
40
41
42
43
...
»

Содержание Xantrex PRO XM 1000














































































Отзывы:

Нет отзывов

Похожие инструкции для Xantrex PRO XM 1000

Бренд: Hama Страницы: 9

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 12

Бренд: Allied Telesis Страницы: 50

DataBender CVX-1300

Бренд: Cypress Страницы: 28

Бренд: CEL-MAR Страницы: 16

L.O.C.PRO LP7-2

Бренд: PAC Страницы: 2

Бренд: Planet Страницы: 36

WIEGAND-Ethernet

Бренд: S4A Страницы: 23

Бренд: Barco Страницы: 2

Бренд: Yuan Страницы: 15

ECO Inverter+ 7

Бренд: Oilon Страницы: 58

SINEMASTER IG4300

Бренд: Kipor Страницы: 50

Бренд: Perle Страницы: 23

Cobalt Alpha Series

Бренд: DCCconcepts Страницы: 25

CTRLink EIMK-100T/FT

Бренд: Contemporary Controls Страницы: 4

Бренд: Sandi Electric Страницы: 32

DC DUAL 21 HP HE

Бренд: Olimpia splendid Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды