Xantrex Xantrex PRO XM 1000 Скачать руководство пользователя страница 29

Страница: 29 / 77

Installation

3–10

975-0263-01-01

Materials

The following checklist is a general list of required materials.

Four corrosion-resistant fasteners sized #10 (M4.5) for mounting the
inverter

Copper DC input cable as calculated in Table 3-1 on page 3–7

Two 3/8 inch (M8) ring terminals sized for the cable diameter to
connect the DC cables to the DC cabling terminal

Lugs and terminals to connect the DC cables that connect to the
battery, disconnect/battery selector switch and fuse holder(s)

DC fuse(s) as calculated in “Calculating Fuse/Circuit Breaker Size”
on page 3–8 and fuse holder(s)

Copper chassis ground cable as specified in Table 3-2 on page 3–7

Ring terminal (appropriately sized to connect copper cable to chassis
ground stud) that meets the following specifications:

•

#8 (M4) stud

•

UL/CSA approved

•

copper

•

tin-plated

Battery isolator (if connecting to a multiple-battery system)

Disconnect/battery selector switch

Optional: 2 × 15 A circuit breakers (XM 1000) or 2 × 20 A circuit
breakers (XM 1800), used for hard wiring the AC input and AC
output to an existing AC circuit.

Optional: Alternator controller

Optional: High-output alternator

1.Consult Appendix B, “Battery Types” and Appendix C, “Alternators and Charging
Systems” to determine whether you need these components.

Important:

The product comes with the items listed on page 2-1. If you have

lost any of these items, an accessory kit of fasteners is available under Xantrex
part number 808-7119. Please visit

www.xantrex.com/buy.asp

to order.

Содержание Xantrex PRO XM 1000














































































Результаты поиска

Содержание Xantrex PRO XM 1000

Отзывы:

Похожие инструкции для Xantrex PRO XM 1000

Бренды по названию

Популярные бренды

Xantrex Xantrex PRO XM 1000, Руководство пользователя

Результаты поиска

Содержание Xantrex PRO XM 1000

Отзывы:

Похожие инструкции для Xantrex PRO XM 1000

Бренды по названию

Популярные бренды