Xantrex RV2012GS Скачать руководство пользователя

Страница: 50 / 64

Operation

3–10

975-0209-01-01

LED Indicator

Charger activity

The RV Series Inverter/Charger has a three-color LED that indicates the activity
of the battery charger. The optional RC/GS or RC7 remote allows custom control
over the charger section of the inverter, including battery type.

Inverter activity

In addition to indicating charger activity, the three-color LED reports on inverter
activity and error conditions.

Table 3-1

LED color and Charger Activity

LED color

LED behavior

Charger Activity

Orange

Solid

Bulk charging

Orange

Flashing

Absorption charge

Green

Fast flashing (four times per second)

Float charge

Orange

Flashing

Equalization charge

Table 3-2

LED color and Charger Activity

LED color

LED behavior

Inverter Activity

Green

Solid

Inverting

Green

Slow flashing (once per second)

Search Mode

Red

Solid

Over current condition

Red

Flashing

Error condition

Содержание RV2012GS

































































Результаты поиска

Содержание RV2012GS

Отзывы:

Похожие инструкции для RV2012GS

Бренды по названию

Популярные бренды

Xantrex RV2012GS, Руководство пользователя

Результаты поиска

Содержание RV2012GS

Отзывы:

Похожие инструкции для RV2012GS

Бренды по названию

Популярные бренды