Xantrex RV2012GS Скачать руководство пользователя | Manualshive

Страница: 28 / 64

background image

Installation

2–10

975-0209-01-01

DC Wiring

Safety Instructions

The inverter’s maximum peak current requirements are high. If battery cables are
too small and/or connections are loose, efficiency and maximum output power are
degraded. Small cables or loose connections can also cause dangerous
overheating of the wire and/or terminals.

Make the battery cables as large and as short as possible. Tape the battery cables
together. This reduces the inductance of the wire, resulting in a better waveform
and reduced stress on the inverter’s filter capacitors.

Refer to Table 2-2 on page 2–12 for recommended battery cable size. Crimped
and sealed copper ring terminal lugs with a 5/16" hole should be used to connect
the battery cables to the DC terminals of the inverter/charger. Soldered cable lugs
are also acceptable.

Code your battery cables with colored tape or heat-shrink tubing.

No DC disconnects are provided as an integral part of this inverter. DC
disconnects must be provided as part of the system installation.

Battery Requirements

Type

Lead-acid deep-cycle battery or group of batteries. The batteries may be a
flooded, gel, or AGM type.

Volts

12 volts

More Information

Go to

www.xantrex.com/support

for more information about batteries.

For detailed information about specific brands of batteries, you will need to
consult individual battery manufacturers.

DC Over-Current Protection

DC fusing

In order to comply with the U.S. NEC, an approved form of battery over-current
protection is required. These installation parts are not supplied with the unit.
Standard-type DC fuses or circuit breakers may be obtained from your dealer,
electrical supply houses.

Xantrex offers a DC rated fuse and holder designed specifically for the RV Series
inverters. This fuse holder is available in a 200, 300, 350 and 400-amp sizes (refer
to Table 2-2 for proper fuse size). See the latest Xantrex RV Catalog or visit

www.xantrex.com

for more information.

CAUTION: Equipment damage

THIS INVERTER IS NOT REVERSE POLARITY PROTECTED. If the positive
terminal of the battery is connected to the negative terminal of the inverter the probable
result is failure of the whole power stage. This type of failure is not covered under
warranty.

«
...
26
27
28
29
30
...
»

Содержание RV2012GS

































































Отзывы:

Нет отзывов

Похожие инструкции для RV2012GS

DCS SCARLATTI DAC

Бренд: Data Conversion Systems Страницы: 26

Бренд: W&T Страницы: 12

Бренд: BSPH Страницы: 36

Бренд: TAMS Страницы: 30

Бренд: Gesan Страницы: 80

Бренд: Peachtree Audio Страницы: 15

EASI ATM IND2x2 Series

Бренд: Teleste Страницы: 28

Бренд: Carbest Страницы: 22

Бренд: Parker Страницы: 172

Бренд: D&H Страницы: 106

Бренд: Bang & Olufsen Страницы: 14

Бренд: Sencore Страницы: 203

Raymarine E22158

Бренд: FLIR Страницы: 48

EBi Direct Interpolation DAC

Бренд: TaKo Electronics Страницы: 7

Бренд: Channel Vision Страницы: 2

PerfectPower PP1000

Бренд: Waeco Страницы: 88

MOVIDRIVE DFC11A

Бренд: SEW-Eurodrive Страницы: 24

FCM 300 PROFIBUS

Бренд: Danfoss Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды