Xantech SMRTP3 Скачать руководство пользователя страница 28

Страница: 28 / 28



Smart Pad

SPECIFICATIONS -- SMARTPAD

Memory: .............. LM110 ................................................................................. 8 kbytes E

PROM

PM110 .............................................................................. 32 kbytes E

PROM

IR Carrier Frequency: ................................................................................ 31.25 kHz to 71.50 kHz

Power Requirements: ........................... 12V DC (75 mA without STATUS - 85 mA with STATUS)

(Requires Xantech 782 Power Supply)

Connector: .......................................... 4-screw terminal block: +12V, STATUS, GND and IR OUT

Conductors: ...............................................Normal 3-wire Xantech IR receiver system compatible

(4th wire for STATUS indication)

Cable Requirements: ......... Four-conductor/24 gauge up to 150', 22 gauge up to 400', 20 gauge

up to 1500' and 18 gauge up to 4000' (unshielded OK)

NOTE:

The Smart Pad

will not operate in the 2-wire Phantom Power Mode.

Maximum peak IR signal output current: .................................................................. 100 milliamps

STATUS Terminal Power Management Turn-on Voltage: .................................... 5 to 30 volts DC

(8mA @ 12V DC)

COM Port: ............................................................................................. RS232 Signal Compatible

Speaker Relay: ................................................................................... Stereo Speaker Pair Muting

Contact Rating: .....................................................................................................2 Amps/30V DC

(Will handle amplifiers rated up to 100W/channel)

IR Commands ...........................................................................ON, OFF, TOGGLE (RC68 Code)

Factory Default Speaker Relay IR Command ................................... #10 Button on RC68, Toggle

Factory Default Code Group Setting ..........................................................................................

Depth behind mounting plate (including terminals): ...................... PM110/LM110: 2-1/4" (57 mm)

EM110: 1-1/8" (29 mm)

• Modules will fit one, two and three-gang boxes for both new and existing construction •

• Modules fit standard decorator-style wall cover plates (not included) •

• Key modules and buttons are available in white, ivory and black •

PATENT PENDING

Windows and Microsoft are registered trademarks of Microsoft Corporation.

2-29-00

Содержание SMRTP3





























Результаты поиска

Содержание SMRTP3

Отзывы:

Похожие инструкции для SMRTP3

Бренды по названию

Популярные бренды

Xantech SMRTP3, Руководство по установке

Результаты поиска

Содержание SMRTP3

Отзывы:

Похожие инструкции для SMRTP3

Бренды по названию

Популярные бренды