Xantech SMRTP3 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 28

Xantech SMRTP3 Скачать руководство пользователя страница 3

3

Controllers



Smart Pad

3

The

CM1N

is similar to the CM1F except that it is set up for use with 6 numeric control buttons as well as

the 5 cursor keys.

Numeric

and

cursor

buttons are included.

The

CM1F

module includes 6 function control keys plus a cursor button cluster with Up, Down, Left, Right,

and Enter keys. The cursor keys can be used with sources that have menu driven on-screen displays.

Cursor

keys and a selection of

function

buttons are included.

The

CM4

is similar to the CM1F except that it is set up for use with 4 source (bank) and 2 function keys as

well as the 5 cursor keys.

Cursor

keys and a selection of

source

and

function

buttons are included.

The

CM6

is similar to the CM1F except that it is set up for use with 6 source (bank) keys as well as the 5

cursor keys.

Cursor

keys and a selection of

source

buttons are included.

The Base Modules

There are three base modules in the

SmartPad

3

system into which the Key Modules are docked. They

contain the electronics for programming & memory (except the EM110) and include flanges for J-box
mounting. An illustration and description of each follow:

CM1N

CM4

CM6

CM1F

CLR MEM

RESTORE

NETWORK

PGM

TRNS

XFER

ERR

CNCL

FULL

DEL

EDIT

DELAY

SEQ

IR

STEP

C
O
M

B A 9 8 7 6

5

4

3

2

1

0

F

E

D

C

PROTECT

WRITE

NETWORK

ADDRESS

PM110

LM110

NETWORK

RESTORE

COM PORT

B A 9 8 7 6

5

4

3

2

1

0

F

E

D

C

WRITE

NETWORK

ADDRESS

PROTECT

EM110

The PM110 dual gang

Programmable Module

is the base module for programming all of the commands

and functions required for each installation. All programming, including sequences (macros), is done with
the PM110 (unless done with Dragon Drop-IR™).

The LM110

Learning Module

is intended for single gang applications and must receive its programming

from a PM110 or Dragon Drop IR™ system. Programs are transferred from the PM110 or Dragon Drop IR
to the LM110 with a 2-step transfer command.

The EM110 is a single gang

Expansion Module

. It has no memory and serves only to expand the number

of key functions for the PM110 in 3-gang configurations.

«
1
2
3
4
5
...
»

Содержание SMRTP3





























Отзывы:

Нет отзывов