XAG P30 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 56

XAG P30 Скачать руководство пользователя страница 54

54

W

a r n i n g

:

•

User needs to read the complete Product Manual and obtain a UAV/RPA system
operation license approved by XAG (or the current laws, regulations and poli-
cies). Failure to do so may cause serious injury to yourself or others, or result in
product damage and property damage. Strong safety awareness is required to
operate this product. This product is not suitable for children. Do not use com-
ponents not provided or recommended by XAG. Be sure to strictly follow the in-
structions of XAG to install and use the product.

•

Familiar with flight environment

•

Avoid obstacles and population

•

CONDUCT Flight safety assessment

•

DO NOT FLY over or above people or in a populous area.

•

DO NOT FLY when you are fatigue, or under influence of alcohol or drugs.

•

DO NOT FLY in any No Fly Zones

•

KEEY AWAY from heat sources to avoid damage to electronics

•

DO NOT conduct solo fight during training, and it is recommended to be supervised by
experienced pilot

•

DO NOT exceed the maximum take-off weight of the UAV/RPAS

•

Ensure that all propellers are in good condition before each flight.

•

DO NOT use aged, chipped or damaged propellers.

•

STAND CLEAR of and DO NOT touch propellers or motors when they are spinning

•

CONDUCT Pre-flight checklist before every flight

•

STRICTLY FORBIDDEN to conduct obstacle avoidance tests on humans or animals
(regardless of static or dynamic) and any objects as obstacles, and it is strictly forbidden
for humans, animals or objects to directly obstruct, interfere or impact the aircraft.

f

l i g h T

s

a f e T y

:

@2020 XAG Australia All Rights Reserved

«
...
52
53
54
55
56
»

Содержание P30

























































Отзывы:

Нет отзывов