XAG P30 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 56

XAG P30 Скачать руководство пользователя страница 42

42

XAG Pre-Flight Checklist

02

Maintenance

01

Inspect and ensure the propellers are in good condition (DO NOT use aged,
chipped or damaged propellers).

02

I n s p e c t a n d e n s u re c l e a n n e s s a n d e n s u re n o s ta i n i s a t ta c h i n g o n to t h e
Propellers.

03

Inspect and ensure the screws securing the Propeller are tighten and not loose.

04

Inspect the integrity of the Airframe.

05

Inspect and observe the screws securing the nozzle and the Landing Skids are
tighten and the module is not loose.

06

Inspect and ensure cleanness and no stain is attaching to the XCope and Terrain
Module

.

07

Conduct Spray System self-check without error.

08

Perform Motor Test to ensure the motor is operating normally and propeller is
rotating in the correct direction.

Clockwise (CW):

Motor 2 & Motor 4

Counter-Clockwise (CCW):

Motor 1 & Motor 3

Normal Communication

√

UAV/RPAS enters RTK mode,

√

UAV/RPAS Heading Accuracy within 2°

√

Number of Satellites >16

09

@2020 XAG Australia All Rights Reserved

«
...
40
41
42
43
44
...
»

Содержание P30

























































Отзывы:

Нет отзывов