manualshive.com logo in svg

XAG P30, Руководство по обслуживанию, Страница: 34 / 56

Поделиться
Скачать
XAG P30 Скачать руководство пользователя страница 34

34

Dual Frequency Antenna 

P20/P30 2019 Dual Frequency Antenna (L)

*1

SKU-01-003-00177

P20/P30 2019 Dual Frequency Antenna (R)

*1

SKU-01-003-00178

M3*12*6 Hexagon socket combination screw

*6

SKU-02-004-00225

M3*8*6 Hexagon socket combination screw

*6

SKU-02-004-00223

 💡

 

What do we need in this section:

1. 

Remove the Airframe Hood, and disconnect the corresponding Dual Frequency cable 
connector.

2. 

Remove the Central Compartment Cover (Refer to Airframe ARM Section), then remove the 
Dual Frequency Antenna feeder protective sleeve and the Dual Frequency Antenna feeder  
from the Air frame Central Compartment Cover.

3. 

Use a 2.5 screwdriver to remove the two (2) screws from the Antenna Mount, and remove 
the feeder form the Airframe Arm.

 

  

The screws using M3*12*6 Hexagon socket combination screw here.

4. 

Use a 2.5 screwdriver to remove the four (4) screws from the Antenna Cover, and remove 
the antenna for replacement.

 

  

The screws using M3*8*6 Hexagon socket combination screw here.

🔧

Disassemble:

@2020 XAG Australia All Rights Reserved 

Содержание P30

























































Отзывы:

Нет отзывов