manualshive.com logo in svg

XAG P30, Руководство по обслуживанию, Страница: 38 / 56

Поделиться
Скачать
XAG P30 Скачать руководство пользователя страница 38

38

1. 

Reassemble the new Pump Controller board back into the original position and secure the 
component with screws, then reconnect the connectors connecting the Peristaltic Pump 
and the Searchlight.

2. 

Reassemble the Peristaltic Pump Housing Top Cover and Peristaltic Pump Housing back 
into the original position and secure each component with screws.

3. 

Reconnect the outlet tube for the Peristaltic Pump Housing.

🛠

Assemble:

I. 

After the reassembly of the Pump Controller Board is completed, perform a spray test of all 
the pumps to confirm the corresponding pump is working normally.

II. 

During reassembly, be aware of the sequence of the connectors (M1, M2, M3, M4) when 
reconnecting.

III. 

During reassembly, be aware and ensure the sealing of the Peristaltic Pump Housing and 
its top cover is installed correctly.

• 

After the reassembly of the Pump Controller Board is completed, perform a spray test of all 
the pumps to confirm the corresponding pump is working normally.

 

IMPORTANT:

🔎 

CHECK :

@2020 XAG Australia All Rights Reserved 

Содержание P30

























































Отзывы:

Нет отзывов