X10 Monitor Plus DC8700P Скачать руководство пользователя страница 14

Страница: 14 / 17

SOLUTION

PROBLEM

If you hear a repetitive trouble alarm
when you try to arm the system, and it
does not arm.

Check the zone indicators. If a door or
window is open, its zone indicator is on.
If there is a problem with a Door/Window
Sensor or Motion Sensor, its zone
indicator flashes slowly. Either:

• Press

DISARM

. Check each Door/

Window Sensor is working properly
and that no doors or windows are
open. Then arm the system. Or:

• While the trouble alarm is sounding,

press

B Y PA S S

to override the

problem zone (its zone indicator then
flashes rapidly). Then arm the
system.

If the alarm trips when you enter the
house before you have time to disarm
it.

Arm the system in the delay mode.

To do this: Set the

MIN/MAX

switch on

the entrance Door/Window Sensor to

MAX

and the Remote Control to

MAX

(Security/Home Automation Remote)
and then press

ARM

• Be sure you set House and Unit

codes on the module(s) to the same
letter and number as downloaded to
the Console (default is A-13).

• Be sure the light you are trying to

control has its on/off switch in the on
position. Be sure its bulb is good.

• Plug the module into another outlet

near the Console.

• Check that the battery indicator on

the Remote Control comes on when
you press a button. Replace batteries
and reinstall remote if necessary.

Lights will not turn on or off from the

LIGHT ON

LIGHT OFF

buttons on

the Remote Control.

TROUBLESHOOTING

PROBLEM

SOLUTION

• Check that the slide switch under the

SETUP flip door is set to

RUN1

RUN2

• Check that the red indicator on the

Remote Control turns on when you
press

ARM

. Replace the batteries

and reinstall the Remote if necessary.

If the system does not arm.

If a zone indicator flashes slowly.

One of the sensors has not reported in,
in the last 4 hours.

Check that the batteries in the sensor
are good.

If you need to arm the system and want
to ignore a sensor which is not
functioning:

1. Press

ARM

on the Remote control.

You year a repetitive trouble alarm to
alert you that there is a problem.

2. While the trouble alarm is sounding,

press

BYPASS

on the Console. The

zone indicator flashes rapidly.

Then press

ARM

on the Remote

Control. The problem zone is not
protected but all other zones are armed.

Note:

if you bypass an open window and

arm the system (as described above)
and later close the window, that zone
will now arm and its zone light will stop
flashing.

You pressed the

BYPASS

button to arm

the system while a sensor was reporting
a problem.

If a zone indicator flashes rapidly.

All manuals and user guides at all-guides.com

Содержание Monitor Plus DC8700P


















Результаты поиска

Содержание Monitor Plus DC8700P

Отзывы:

Похожие инструкции для Monitor Plus DC8700P

Бренды по названию

Популярные бренды

X10 Monitor Plus DC8700P, Руководство пользователя

Результаты поиска

Содержание Monitor Plus DC8700P

Отзывы:

Похожие инструкции для Monitor Plus DC8700P

Бренды по названию

Популярные бренды