X-TREME XB-420M Скачать руководство пользователя | Manualshive

Страница: 25 / 43

background image

24

TROUBLESHOOTING GUIDE

Problem

Cause

Solution

Battery gauge
does not register
anything when
vehicle is on.

1. Loose connection near
the power switch or
battery pack.
2. Battery is completely
discharged.

1. Check the connections,
reconnecting any that are
loose.
2. Charge the battery.

Battery gauge
registers but
vehicle still does
not work.

1.  Motor wire is loose or
disconnected.
2.  Throttle is defective.
3.  Controller is defective.

1. Send to service to repair
the wiring.
2. Replace Throttle
3. Replace Controller.

Clicking noise
coming from
motor.

1. Chain is loose.
2. Magnets in motor have
come loose.

1. Adjust the chain.
2. Send to customer service
to replace a new motor.

Vehicle does not
stop when
Throttle returns
to original
position.

Controller or Throttle is
defective.

Replace Controller or
Throttle. Customer service
can assist in diagnosis.

Vehicle is losing
speed.

1.  Battery is low.
2.  Defective battery.
3.  Defective Throttle.

1.  Charge battery.
2.  Replace battery.
3.  Replace Throttle

Distance per
charge is
reduced.

1. Tire pressure is low.
2. Battery is not fully
charged.
3. Battery is damaged.
4. Headwind, slopes,
overloading, etc.

1. Fill Tires with sufficient
pressure.
2. Charge battery for 6-8
hours.
3. Replace Battery
4. Reduce these factors.

Battery could
not be charged.

1. Loose wiring near the
charging socket.
2. Loose wiring in battery
pack.
3. Defective Charger.

1. Check the wiring, re-
establish connection.
2. Send to a qualified service
technician.
4. Replace Charger.

NOTE: if other problems occur, do not attempt to disassemble the
electric scooter on your own, please contact your retailer or

www.x-tremescooters.com/support

.

«
...
23
24
25
26
27
...
»

Содержание XB-420M












































Отзывы:

Нет отзывов

Похожие инструкции для XB-420M

Бренд: E-max Страницы: 42

Бренд: b'Twin Страницы: 18

ICe Q5 EVOLUTION

Бренд: Ice Страницы: 34

Бренд: HOMCOM Страницы: 16

BEWEGT MIT KOMFORT

Бренд: Stark Products Страницы: 40

Бренд: Wisper Страницы: 13

Бренд: Meyra-Ortopedia Страницы: 56

Бренд: Leader Fox Страницы: 17

Бренд: Rollplay Страницы: 23

Бренд: E-Plus Страницы: 17

Бренд: X-TREME Страницы: 20

Бренд: X-TREME Страницы: 35

Бренд: X-TREME Страницы: 44

Бренд: Kaabo Страницы: 12

Бренд: DAELIM Страницы: 222

Бренд: Quingo Страницы: 78

Бренд: Force Moov Страницы: 67

Бренд: Jetson Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды