background image

time to reach  full power. The unit will  stay  “warm”  for  some time even  if 
off.

This  fixture does  not have a  set duty  cycle but  we  do  not  recommend 
using it for more than four hours continuously.

From  time  to time be  sure  to clean  the  aperture with  a  dry  tissue  that 
does not pill. You  may also use an alcohol prep  wipe and compressed air 
to blow dust from the vents. BE SURE  the alcohol has  dried fully before 
activating the laser. This is the only user allowed maintenance.

Always keep  all factory supplied labels on the unit and visible. These are 
all required for legal compliance. 

During  any  use  of  your  X-Laser

®

  product,  be  sure  to  leave  an  open 

space around  all  sides  of the laser  to facilitate airflow  through  the unit. 
Do not obstruct the holes in  the casing as these permit air  to enter  and 
cycle though the unit.

Temperature and Lasers

Lasers work  best at room  temperature with colder  and warmer  tempera-
tures resulting in  inconsistent performance. Always ensure that the laser 
housing  has  excellent  airflow  around  the  case  and  that  the  air  is  no 
colder than  sixty degrees and no warmer  than ninety degrees. Failure to 
do  so  may  result  in  weak  output,  overly  strong  output  (this  is  also  a 
safety issue!)  which  will  diminish  the life of the unit and/or  large output 
power  swings. All  X-Laser

®

  products  are  thermostatically  monitored so 

we  can  determine if a  diode failure  was temperature related.  Such  fail-
ures  are NOT  covered under our  manufacturer’s warranty. Extreme cold 
and hot temperatures  WILL cause a  diode failure. Keep  this unit climate 
controlled at ALL times.

Getting Started

Unpacking

Your new X-Pod system should contain the following items:

One X-Pod Router,
Up to 8 X-Pod head units,
Up to 8, 10 foot CAT-5 cables,
A grounded power cable,
This user manual,
A DVD containing letters, forms, and a wealth of other information 
about this product specifically and laser safety in general.

Page 9   of 18

Содержание X-Pod



















Отзывы: