Würth SBS 18-A, Перевод оригинальной инструкции по эксплуатации

Страница: 17 / 202

17
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted sound pressure level of the product
is 77 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745:
Cutting board: a
h
=24 m/s
2
, K=1.5 m/s
2
,
Cutting wooden beam: a
h
=24.5 m/s
2
, K=1.5 m/s
2
.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main appli-
cations of the tool. However if the tool is used for different appli-
cations, with different accessories or insertion tools or is poorly
maintained, the vibration emission may differ. This may signifi-
cantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
sories, keep the hands warm, organisation of work patterns.
EC-Declaration of Conformity
We declare under our sole responsibility that the product
described under “Tool Specifications” is in conformity with all
relevant provisions of the directives 2011/65/EU,
2014/30/EU, 2006/42/EC including their amendments
and complies with the following standards:
EN 60745-1, EN 60745-2-11.
Technical file (2006/42/EC) at:
Adolf Würth GmbH & Co. KG, PCM,
Reinhold-Würth-Straße 12–17
74653 Künzelsau, Germany
Künzelsau: 07.07.2014
Battery Charging

Use only the chargers listed in the technical
data. Only these chargers are matched to the lithium-ion
battery of your power tool.
Note: The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the first
time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.

Do not continue to press the On/Off switch
after the machine has been automatically
switched off. The battery can be damaged.
Observe the notes for disposal.
Removing the battery
The battery 9 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 8 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery
9 , press the battery unlocking button 8
and pull the battery out of the power tool toward the rear. Do
not exert any force.
Battery Charge-control Indication
(see figure A)
The three green LEDs of the battery charge-control indicator
12 indicate the charge condition of the battery 9 . For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button
11 to indicate the charge condition. This is also
possible when the battery 9 is removed.
When no LED lights up after pushing button 11 , then the bat-
tery is defective and must be replaced.
Marcel Strobel
Head of Product
Management
Dr.-Ing. Siegfried Beichter
Head of Quality,
Authorized Signatory
LED Capacity
Continuous lighting 3 x green  2/3
Continuous lighting 2 x green

1/3
Continuous lighting 1 x green <1/3
Flashing light 1 x green Reserve
OBJ_BUCH-2241-001.book Page 17 Tuesday, July 22, 2014 1:21 PM