Wulfsberg FLEXCOMM II C-5000 страница 136 Скачать руководство пользователя

Страница: 136 / 151

FLEXCOMM

C-5000 (Non-Digital)

Installation Manual

150-1355-000 Rev. M

CONFIDENTIAL AND PROPRIETARY TO COBHAM

Page 136

D. Checkout Procedure (Continued)

(4) At this point the C-5000 must have its configuration programmed. Using either the

Wulfsberg RP software or the front panel knobs and buttons, program the required

system configuration data.

(5) The final programming step is to program the desired preset channels into the C-5000

using either the Wulfsberg RP software or using the front panel knobs and buttons. Start

with a limited set that will test the basic operations of the system such as:



Analog FM Modulation at a frequency in each band: 30-50, 138-174, 225-400,400-512,

806-870.



AM Modulation at a frequency in each band: 118-137, 225-400.



Encryption if available in the transceiver.

(a)

On the C-5000, tune transceiver system #1 to the manual channel. Using the

"EDIT" page on the C-5000 tune the manual channel for 30 MHz Rx and Tx

frequency, set Tx Power to Hi, and the Bandwidth to "S", no subaudible tone.

Press the "CLR" button to return to the "HOME" display page.

(b)

Press the "Test" Button and verify the squelch indicator lights up and noise audio

is heard in the headsets. Adjust RT #1 volume control (the small inner knob on

the left side) so that the noise can be heard.

(c)

If a single channel guard receiver or synthesized guard receiver is present

(-0201, -0301, -0401, -0501), select the guard receiver and press the "TEST"

button. Verify the squelch indicator lights and audio is heard.

(d)

If a second transceiver is in the system, select the manual channel for RT #2 and

input the same settings that were done to RT #1. Press the "Test" button to open

squelch and verify the squelch indicator for transceiver #2 lights and audio is

heard. If an audio panel is being used, make sure selector switches are in the

correct position to hear both Primary (RT #1) and Secondary headset audio (RT

#2).

(e)

Repeat (d) with transceiver #3.

Transmitter Tests

A. General
During transmitter verification tests, monitor any other radios or sensors that are present to
determine if interference between them and the C-5000 system exists.

(1) Input a 1 kHz sinewave tone into the primary microphone port and adjust input level for

.25 VRMS. DO NOT RELY ON THE TEST EQUIPMENT SETTING - MEASURE USING

AN AC VOLTMETER AT THE MICROPHONE JACK.

(2) Set the communication analyzer to FM mode. Tune the manual channel on the C-5000 to

the frequencies listed in Tables 1.0 through 1.5 (select appropriate transceiver model)

and record transmit power and modulation levels at the output of the radio. This will

verify the C-5000 is communicating with the transceiver and that microphone audio is

getting to the transceiver at the proper level. Verify that the C-5000 indicates a transmit

condition by showing the transmit indicator when the PTT is initiated. If modulation is not

Содержание FLEXCOMM II C-5000
























































































































































Результаты поиска

Содержание FLEXCOMM II C-5000

Отзывы:

Похожие инструкции для FLEXCOMM II C-5000

Бренды по названию

Популярные бренды

Wulfsberg FLEXCOMM II C-5000, Руководство по установке

Результаты поиска

Содержание FLEXCOMM II C-5000

Отзывы:

Похожие инструкции для FLEXCOMM II C-5000

Бренды по названию

Популярные бренды