Worx WG761, Руководство пользователя

Страница: 15 / 36

15
Cordless Lawn Mower EN
Check balance of blade by placing center hole in blade Q-1
over a screwdriver shank Q-2, clamped horizontally in a vise
Q-3. If either end of the blade rotates downward, file that
end. Blade is properly balanced when neither end drops.
BLADE MAINTENANCE (See Fig. R1, R2)
Replace yourMower Blade after 50 hours mowing or 2 years,
which ever is the sooner-regardless of condition.
Follow these procedures to remove and replace the Blade.
You will need garden gloves (not provided) and a spanner
wrench (not provided) to remove the Blade. Make sure bat-
teries are not installed. Wedge a block of wood between the
blade and the mower deck to prevent the blade from turning
and unscrew the Blade Bolt counter-clockwise using a span-
ner wrench, and then remove the Blade.
To re-assemble, position the Blade with the cutting edges
towards the ground. Then securely tighten the Blade Bolt.
For Battery tools
The ambient temperature range for the use and storage of
tool and battery is 0°C-45°C (32°F-113°F).
The recommended ambient temperature range for the
charging system during charging is 0°C-40°C (32°F-104°F).
TROUBLESHOOTING
PROBLEM SOLUTION
1. Mower doesn’t
run when
Operating Bail is
activated.
A. Check to make sure Safety lock-
out button is completely pushed.
B. Release Operating Bail to turn
mower off. Remove batteries, turn
mower over and check that blade is
free to turn. If not free, return to an
authorized servicer. Blade should
turn freely.
C. Has battery been fully charged?
Plug in charger and wait for green
light to come on.
2. Motor stops
while mowing.
A. Release Operating Bail to turn
mower off. Remove batteries,turn
mower over and check that blade is
free to turn. If not free, return to an
authorized servicer. Blade should
turn freely.
B. Raise cutting height of wheels to
highest position and start mower.
C. Has battery been fully charged?
Plug in charger and wait for green
light to come on.
D. Avoid overloading the mower. Slow
down the cutting pace by pushing
mower slower or raise the cut height.
Or both.
3. Mower runs
but cutting
performance is
unsatisfactory,
or does not cut
entire lawn.
A. Has battery been fully charged? Plug
in charger and wait for green light to
come on.”
B. Release Operating Bail to turn mower
off. Remove batteries. Turn mower over
and check: Blade for sharpness - Keep
blade sharp. Deck and discharge chute
for clogging.
C. Wheel height adjustment may be set
too low for grass condition. Raise cutting
height.
4. Mower is too
hard to push.
A. Raise cutting height to reduce
deck drag on grass. Check each
wheel for free rotation.
5. Mower is
abnormally
noisy and
vibrates.
A. Release Operating Bail to turn
mower off. Remove batteries. Turn
mower on side and check blade
to ensure it has not been bent or
damaged. If blade is damaged,
replace with a replacement blade.
If the underside of the deck is
damaged return mower to an
Authorized service center.
B. If there is no visible damage to the
blade and the mower still vibrates:
Release Operating Bail to turn mower
off, Remove batteries, and remove
blade. Rotate blade 180 degrees and
retighten. If mower still vibrates,
contact customer service.
6. Vibration
sensation and/
or swooshing
sound
coming from
underneath
deck.
A. Wet grass and/or debris has
collected to the inner wall of the
deck, creating unbalanced airflow.
Remove batteries and remove debris
from inner deck wall.
7. Battery
charger LED’s
not on.
A. Check plug connection.
B. Replace charger.
8. Battery
charger LED
does not flip to
green.
A. Battery needs to be diagnosed.
Take to authorized service center.
9. Mower not
picking up
clippings with
the Grass
Collection Bag.
A. Remove mulch plate when
bagging.
B. Chute clogged. Release Operating
Bail to turn mower off. Remove
batteries. Clear chute of grass
clippings.
C. Too much cut grass. Raise cutting
height of wheels to shorten length
of the cut.
D. Bag full. Empty bag more often.