manualshive.com logo in svg

Workzone Titanium DBAF50/40, Инструкция по эксплуатации, Страница: 9 / 18

Поделиться
Скачать
Workzone Titanium DBAF50/40 Скачать руководство пользователя страница 9

AFTER SALES SUPPORT

e-mail: [email protected]

1800 909 909 (toll free)

MODEL No.: DBAF50/40  •  61420  •  07/2018

AFTER SALES SUPPORT

e-mail: [email protected]

1800 909 909 (toll free)

MODEL No.: DBAF50/40  •  61420  •  07/2018

16

17

Important information – Product care

NOTE: Xfinity Battery and Charger not included. For any issues related 

directly to your purchased ALDI Xfinity Battery / charger, contact the 

Customer Service of the manufacturer as listed on the battery / charger 

packaging, manual or on the label on the battery / charger.
This Brad Nailer / Stapler uses Lithium Ion Battery Cells. Care MUST be taken to 

ensure both the safety and life of the pack is maintained. Ensure you have read all 

of the safety notes in the previous pages before using the Brad Nailer / Stapler.
Treat the battery pack with care and within the guidelines of this manual and the 

supplied manual included with the purchase of ALDI Xfinity Battery/s.
If the battery pack does become immersed in water or any fluids, or is subject 

to a severe drop or it does not operate within the guidelines of this manual 

or the supplied manual included with the purchase of ALDI Xfinity Battery/s, 

immediately STOP using the battery pack and have it checked. During operation 

avoid overloading the Brad Nailer / Stapler. If the Brad Nailer / Stapler is 

overloaded it will automatically STOP. Overloading may occur for a number of 

reasons including when the Brad Nailer / Stapler is pushed too hard or when 

using a Nail / Staple greater than what is specified, or there is a nail / staple jam. If 

you do overload the Brad Nailer / Stapler during operation refer to the “Overload 

Protection” section in this manual.
NOTE: When the battery of the Brad Nailer / Stapler is at the lower end of the 

charge, the Brad Nailer / Stapler is more susceptible to the overload condition. 

Running the Brad Nailer / Stapler at close to maximum load, or continual resetting 

of the overload will cause the battery pack to overheat. When a preset cell 

temperature is detected, the battery pack will automatically STOP operating and 

will not restart until the battery pack has cooled to a safe level.
In this condition, DO NOT force the cooling down of the pack by placing in a 

freezer or similar device. Refer to the “Overload Protection” section in this manual.
Another feature of the Brad Nailer / Stapler is the low voltage cut out feature. This 

feature operates when the voltage drops below a preset value. When this occurs 

the tool will automatically stop operating. To correct the situation you need to 

either insert another charged battery into the Brad Nailer / Stapler or recharge the 

existing battery, and then proceed with the Brad Nailer / Stapler application.
NOTE: Attempting to restart the tool in this condition without either recharging 

the battery or installing a battery with charge will lead to Brad Nailer / Stapler 

restarting and then stopping again after only a few seconds of operation.
These safety devices have been fitted for the safety, reliability and life of the tool.

Assembly

Fitting and removing the Battery from the Brad Nailer / 

Stapler and Charger.

NOTE: (Xfinity Battery pack and charger is not included with 

this product; it is shown only for illustrative and instructional 

purposes only)

1.   To install your purchased Xfinity battery (17) on to the Brad Nailer / 

Stapler, align the grooved guide rails of the battery (17) with the raised 

guide rails on the bottom of the Brad Nailer / Stapler.  With your thumb 

on the battery release tab on the battery pack, slide it firmly into the 

handle until the battery is secure in position (Fig A). Release your thumb 

from the battery release tab. When the battery is secured you will hear it 

engage with a snap / click.

2.   To remove the battery (17) from the Brad Nailer / Stapler, press the 

battery pack release button and slide the battery (17) completely out 

and away from the Brad Nailer / Stapler (Fig B).

3.   When applying the battery (17) onto your purchased Xfinity charger 

(18), align the grooved guide rails of the battery (17) with the raised 

guide rails on the charger (18) (Fig C). The charger (18) will make a snap 

/ click noise when it is securely aligned.

A.

B.

Содержание Titanium DBAF50/40



















Отзывы:

Нет отзывов