AFTER SALES SUPPORT
e-mail: [email protected]
1800 909 909 (toll free)
MODEL No.: DBAF50/40 • 61420 • 07/2018
AFTER SALES SUPPORT
e-mail: [email protected]
1800 909 909 (toll free)
MODEL No.: DBAF50/40 • 61420 • 07/2018
26
27
CAUTION! Electrical and battery operated units that no longer work
should not be disposed of in the household waste! They are to be collected
separately, in accordance with your local waste disposal regulations.
ATTENTION! Batteries must be removed from battery powered tools
and disposed of separately in accordance with relevant waste battery
regulations.
Batteries must never be disposed of with domestic waste!
Please discard power tools no longer usable at a local collection point.
Collection and disposal of packaging materials separately by types
complying with local rules and regulations. For details, please contact your
local council.
Warranty
Your new WORKZONE® TITANIUM 20V Lithium-Ion Brad Nailer / Stapler will
more than satisfy your expectations.
It has been manufactured under stringent WORKZONE® TITANIUM Quality
Standards to meet superior performance criteria.
You will find your new 20V Lithium-Ion Brad Nailer / Stapler easy and
safe to operate, and, with proper care, it will give you many years of
dependable service.
CAUTION. Carefully read through this entire instruction manual before
using your new WORKZONE® TITANIUM 20V Lithium-Ion Brad Nailer /
Stapler.
Take special care to heed the Cautions and Warnings.
Your WORKZONE® TITANIUM 20V Lithium-Ion Brad Nailer / Stapler
has many features that will make your job faster and easier. Safety,
performance, and dependability have been given top priority in the
development of this 20V Lithium-Ion Brad Nailer / Stapler, making it easy
to maintain and operate.
Use only WORKZONE® TITANIUM replacement parts for your product.
Non-conforming parts or modifications made to parts will void your
warranty.
Environmental protection
Recycle unwanted materials instead of disposing of them as waste.
All tools, hoses and packaging should be sorted, taken to the local
recycling centre and disposed of in an environmentally safe way.
Overload Protection
If the LED battery and function indicator (10) is flashing green, the Brad nailer
/ stapler has overloaded / overheated possibly from extended use. Remove
the battery immediately and allow the unit to sit for 30 minutes – 1 hour.
When the Brad nailer / stapler has cooled, re-install the battery and check the
LED battery and function indicator (10) is no longer flashing green. If it is no
longer showing green, continue to use the Brad nailer / stapler.
If the Brad nailer / stapler continues to result in an overload / overheated
condition, DO NOT continue to use and make contact with customer service
by calling 1800 909 909 or emailing [email protected] for
service advice.
Maintenance
Magazine Maintenance
WARNING: Ensure to remove battery pack from the tool during
cleaning and maintenance.
Ensure that no debris or dust enter the open magazine as this may cause
jamming or malfunction. Clean the inside of the magazine with a fine brush
or clean cloth. An air sprayer may also assist with removing any accumulated
dust or debris.
Cleaning
Avoid using solvents when cleaning plastic parts. Most plastics are
susceptible to damage from various types of commercial solvents and may
be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
Transport
When transporting the nailer / stapler, it is recommended to remove the
battery from the unit, remove any nails or staple cartridges in the unit to
avoid any potential misfiring, and store in a secure case or the packaging box
during transport.
Battery Maintenance
To maintain battery capacity, always refer to the specific instructions in the
supplied manual included with the purchase of ALDI Xfinity Batteries. It is
recommended to recharge your battery every two months. Store only fully
charged batteries. They should therefore be recharged from time to time. The
place of storage must be dry.