Worcester WM 12 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 37

Worcester WM 12 Скачать руководство пользователя страница 8

7.1

The appliance is supplied with a telescopic flue system that

caters for 102mm (4 inch) to 460mm (18 inch) Wall thickness.
For details of the installation procedure refer to Section 11.6. of
these installation and servicing instructions.

7.2 Siting the flue outlet terminal
1.

The flue outlet terminal must be located in a suitable position,

as shown in fig.8, such that the products of combustion can be
freely dispersed without the possibility of the gases entering the
dwelling or that of a neighbouring dwelling. The flue outlet can
be seen in figs. 6 and 7.

2.

Discharge of flue gases into car ports or narrow passageways

is not recommended.

3.

The terminal must not cause an obstruction nor the discharge

cause a nuisance as a result of either flue gases or terminal noise.

4.

If the terminal is fitted within 600mm of a plastic/painted gut-

ter or painted eaves then an aluminium or stainless steel shield
at least 750mm long should be fitted to protect the surface.

5.

If a terminal is fitted less than 2 metres above a surface to

which people have access a terminal guard should be fitted. A
flue terminal guard kit is available from Worcester, Bosch Group,
Part Number 7 716 190 017.

6.

When fitting the flue terminal guard refer to the instructions

supplied with the flue terminal guard kit.

7. Flue System

8

Fig. 6. Flue installation

442

131

104

96

442

328

65

417

A

A

FRONT VIEW

SIDE

VIEW

A

Flue outlet

B

Wall trim

C

External cover

C

C

Flue

terminal

guard

(optional

extra)

See fig. 8 for flue outlet
terminating positions.

Fig. 7. Flue location

External duct

Locating tabs

Flue
outlet

Seal

Splash plate

External Cover

NOTE:

The Splash plate/seal

should be hard up against
the External Cover.

5mm Minimum

49

B

NOTE

: Ensure a minimum gap of 5mm between the external

cover and wall trim to allow sufficient air for combustion.

Locating slot

Flue locating tab

Flue locking screw

104

«
...
6
7
8
9
10
...
»

Содержание WM 12






































Отзывы:

Нет отзывов