background image

Opti-Link 

            

WOODWAY 

Installation and Operation 

Woodway Engineering Ltd 

  OPTINS-4.0 Rev 4 

Page 7 of 9 

December 2007 

 

Troubleshooting 

The following table is a guide to the most common problems and assumes that the equipment under control is fully 
functioning. 

 

Problem Possible 

Cause(s) Solution(s) 

Total system failure 

Blown fuse. 

Check power supply and connections to 
modules. 

  Single switch operation on handset 

is ok but multiple switch operation 
fails or causes system shutdown. 

 

  Lightbar control failure 

Communications fault. 

  Check Data link connections are 

secure. 

  Check inputs and cable ends are 

clean. 

Low voltage. 

Check battery voltage has not dropped 
below 12V. 

  Red LED illuminated on 

Output/Receiver module 

  When selecting more than one 

switch function some lights are on 
others are not. 

  Light operation appears to be 

‘haywire’ 

Excessive current draw on one or 
more channels. (Maximum working 
current is 0.5 amps (500mA) per 
channel).  

To locate the faulty channel, Operate 
each switch individually until the Red 
LED illuminates.  

  Check for short circuit in wiring. 

  Check for faulty equipment. 

If problem still persists replace 
Output/Receiver Unit 

No output from Output/Receiver. 

‘Data OK’ led is not flashing 

Communication fault. 

Check Data link connections are secure. 

High pitch ‘whistle’ from the speaker 
on PA operation 

Volume set too high. 

Turn the pot anti-clockwise to reduce the 
volume. (See Fig. 2) 

Keypad and speaker too close 
together 

Increase the physical separation 
between the keypad and the speaker 

The Keypad led is flashing. 

Low Voltage 

 

Check that the voltage is healthy. 

For 12V systems >9.5V 

The keypad led is permanently on 
and the system is not functioning 

Internal eprom fault 

Replace keypad 

One or more switches will not remain 
on. 

Switches are set for momentary 
operation. 

Reset the switches to latching operation 
(See Keypad Programming on Page 6) 

Pressing one switch ‘On’ turns the 
previous one ‘Off’. 

Switches are set to ‘self-cancelling’. 

Reset the switches. ( See Keypad 
Programming on Page 6) 

When selecting ‘360’ the lightbar is 
not functioning 

Switches are incorrectly set. 

For the ‘360’ to function correctly when 
connected to a Woodway lightbar only 
SW1 can be used as 360 and the 
‘Special Strobe Function’ must be set. 

(See Keypad Programming on Page 5) 

Switch panel cannot be programmed.   Keypad has lockout still enabled. 

Disable lockout (see page 5) 

Switches 3, 13 and 14 have no 
output. 

A ‘special’ programme setting has 
been enabled. 

To disable the programme setting put the 
keypad into programming mode and 
press and hold SW11 and SW14 until a 
beep is heard. 

When the door is opened a beeper is 
heard. 

Door switch has been connected but 
the handbrake has not been 
connected or the handbrake has not 
been applied. 

If the door switch is connected into the 
system, the handbrake must also be 
connected. The beeper acts as a 
‘handbrake off’ warning. 

Содержание Opti-Link











Отзывы: