background image

Opti-Link 

            

WOODWAY 

Installation and Operation 

Woodway Engineering Ltd 

  OPTINS-4.0 Rev 4 

Page 5 of 9 

December 2007 

 

Keypad Programming 

WARNING! Keypad programming should only be carried out with either the 
data wire to the receiver disconnected or the receiver output connector 
removed to prevent un-intentional operation of the vehicle equipment.

 

Changes to the keypad settings should not be carried out with the vehicle engine 
running

Keypad Lockout 

In normal use the keypad is locked to prevent changes to the keypad function. Keypad 
functions cannot be changed until the lock is disabled. To disable the lock press and hold 
switches 1, 4, 7, 12 and 14 until a beep is heard. The led at the top of the panel will be 
permanently on. To enable the lock press and hold SW13 and SW14 until a beep is 
heard. The keypad will de-activate. To re-activate press any key. 

To program P1: 

Press and hold down P1 until the confirmation beep is heard (5 seconds approx). 
P1 will flash and the current program setting, if any, will be activated. All 
programmed switches will be illuminated. 

Select the new combination of buttons to activate with P1 by activating/de-

activating buttons 1 to 13, leaving only those buttons required illuminated. 

When the selection is complete, do not press any other button until the beep is heard to confirm the programme. 
(Approximately 10 seconds from the last selection). P1 will stop flashing when programmed. 

Reset the keypad by pressing the Reset button. 

To program P2, repeat as for P1. 

Switch self-cancelling mode: 

In some situations it may be preferable to have buttons self-cancelling, i.e. if one button in the row is active pressing 
another one in the same row will cancel it. This is possible for individual rows of buttons, i.e. 

1 - 3

4 - 6

7 – 9, 10 -12

 and 

a self cancelling bank 

7 – 12 

To program the buttons for self-cancelling mode: 

Press and hold down the first button on the row, i.e.1, 4, 7 or 10 and, at the same time, press and hold down SW14 until a 
beep is heard. Repeat this procedure for further row settings.  

Buttons 

7

 to 

12

 may be a self-cancelling bank. To set this option, press the 

Reset Button

 and button 

12

To cancel the self-cancelling mode, repeat the above procedures. 

To program the buttons for momentary or latching operation: 

The default setting for switches 1-12 is latching. To change any switch from latching to momentary operation or vice-
versa; 

1  Press and hold down SW13 and the switch to be changed for 5 secs until a confirmation beep is heard 

2  Release both switches and press SW14. 

Special Strobe Setting: 

The special strobe setting is only applicable to switches 1 to 3 and is usually set when the system is used to control ‘360’ 
light selection on a Woodway lightbar. When this option is set pressing SW1 will also activate SW2 and SW3. 

1  Press and hold down SW14 and switch 2 until a confirmation beep is heard. 

2  Release both switches. 

3  To cancel the setting, repeat the procedure. 

External 999 Input 

To enable this function. 

1  Press and hold SW6 and SW14 until a beep is heard. 

To cancel the setting, press SW3 and SW14 until a beep is heard 

Содержание Opti-Link











Отзывы: