background image

Opti-Link 

            

WOODWAY 

Installation and Operation 

Woodway Engineering Ltd 

  OPTINS-4.0 Rev 4 

Page 1 of 9 

December 2007 

 

Disclaimer 

This document is intended to be used as a reference guide for the installation and operation of the Opti-Link Control 
System. 

Every effort has been made to ensure the reliability and accuracy of the information contained in this manual at the time of 
going to press. However, specifications and procedures are subject to change due to our constant endeavours to meet 
customer requirements, and to maintain a research and development process of continuous improvement for all 
Woodway products.  

Woodway Engineering Ltd reserves the right to make changes in product and documentation specifications and 
procedures at any time and without notice. The information contained in this manual is believed to be reliable and 
accurate with regard to the Opti-Link Control System. The company shall not be held liable for improper installation, 
operation, or maintenance of the system in circumstances where procedures and specifications have not been followed 
correctly. It is essential therefore, that you follow the specifications, procedures, and recommendations outlined in this 
manual. 

©2005 Woodway Engineering Ltd. All Rights Reserved 

 

Important Installation and Safety Notes 

 

 

 

Modules and connectors are not waterproof. Install modules and cables in a dry 
location away from excessive heat, humidity and any components likely to 
damage the system. 

It is the installer’s responsibility to ensure that; 

ƒ

 

the method of installation does not damage or interfere with vehicle 
equipment and wiring. 

ƒ

 

if the vehicle is fitted with airbags, the installation does not interfere 
with the operation or effectiveness of the airbags or will cause the 
equipment to become a projectile that could cause death or injury. 

ƒ

 

all connections to chassis are taken direct to the battery. 

ƒ

 

fuse ratings are changed to suit specific applications.  

The proximity of certain radio equipment may interfere with Opti-Link data 
transmission. To reduce this possibility, Opti-Link and radio equipment wiring 
should always be kept well apart and should not, under any circumstances, be 
harnessed or fastened together. 

The installers should supply all mounting fixings. 

It is the user’s responsibility to ensure that; 

ƒ

 

the system is used in a safe and responsible manner to ensure the 
safety of both themselves, their passengers, other road users and 
pedestrians. 

ƒ

 

the system and its installation are properly maintained to ensure its 
effective operation. 

 

Failure to follow these notes and safety guidelines may result in damage to the 
product and/or vehicle and may cause injury to personnel or bystanders. 

 

 
 

 

Содержание Opti-Link











Отзывы: