Woodstar 3906812952, Перевод оригинального руководства по эксплуатации, Страница: 23 / 44


www.scheppach.com

service@scheppach.com

+(49)-08223-4002-99

+(49)-08223-4002-58
23 І 44
Noise and vibration values
The total noise values determined in accordance with
EN 61029.
sound pressure level L
pA
72,6 dB (A)
uncertainty K
pA
3 dB
sound power level L
WA
82 dB (A)
uncertainty K
WA
3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 61029.
Vibration emission value ah = 1,58 m/s
2
K uncertainty = 1,5 m/s
2
The specified vibration value was established in
accordance with a standardized testing method. It may
change according to how the electric equipment is used
and may exceed the specified value in exceptional
circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
6. Assembly
Column and machine foot, Fig. 3
1.
Set the machine foot (1) down on the ground or the
workbench.
2. Place the column (2) on the base plate so that the
holes on the column (2) align with the holes on the
base plate (1).
3. Screw the hexagonal screws (A) to fasten the column
into the base plate and tighten them using a hexagon
spanner.
Table and pillar, Fig. 4
1. Slide the drilling table (3) onto the pillar (2). Position
the table directly above the base plate.
2. Install the table bolting (F) in the table unit from the left
side and tighten it.
Machine head and pillar, Fig. 5
1. Place the machine head (4) onto the pillar (2).
2. Put the spindle of the drilling machine with the table
and the base plate in the cover and fasten the 2 Allen
screws (G).
Drill chuck protection with depth stop, Fig. 6
Fit the chuck protection with depth stop (8) onto the
spindle pipe and tighten the slotted screw (H).
Caution! The depth stop must be fed through the dril-
ling (I) on the housing. Screw on the two nuts (J1/2) and
place the indicator (K) onto the depth stop. The indicator
(K) must point at the scale.
Residual risks
The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use of
improper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instruc-
tions“ and the „Proper use“ are observed along with
the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the machine
in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Hands may never enter the processing zone when the
machine is in operation. Release the handle button
and switch off the machine prior to any operations.
• Prior to any adjustment, maintenance or service work
disconnect the mains power plug!
5.Technical Data
Nominal input voltage 230 V~/50 Hz
Power rating 500 W (S2 15min)
Motor speed 1450 min
-1
Output speed (infinitely
adjustable)
550 -2500 min
-1
Drill chuck mount B16
Drill chuck 1,5 - 16 mm
Dimensions of drill table 164 x 162 mm
Angle adjustment of table 45°/0°/45°
Drill depth 50 mm
Pillar diameter 46 mm
Height 590 mm
Base area 298 x 190 mm
Weight 15,5 kg
Laser class II
Wavelength of laser 650 nm
Laser output < 1 mW